LTC3890EGN-1 LINER [Linear Technology], LTC3890EGN-1 Datasheet - Page 12

• Manufacturer Part Number: LTC3890EGN-1
• Description: 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller
• Manufacturer: LINER [Linear Technology]

OPERATION
LTC3890-1
Light Load Current Operation (Burst Mode Operation,
Pulse Skipping, or Forced Continuous Mode)
(PLLIN/MODE Pin)
The LTC3890-1 can be enabled to enter high effi ciency
Burst Mode operation, constant frequency pulse skipping
mode, or forced continuous conduction mode at low load
currents. To select Burst Mode operation, tie the PLLIN/
MODE pin to a DC voltage below 0.8V (e.g., SGND). To
select forced continuous operation, tie the PLLIN/MODE
pin to INTV
PLLIN/MODE pin to a DC voltage greater than 1.2V and
less than INTV
When a controller is enabled for Burst Mode operation, the
minimum peak current in the inductor is set to approxi-
mately 25% of the maximum sense voltage even though
the voltage on the ITH pin indicates a lower value. If the
average inductor current is higher than the load current,
the error amplifi er, EA, will decrease the voltage on the
ITH pin. When the ITH voltage drops below 0.425V, the
internal sleep signal goes high (enabling sleep mode)
and both external MOSFETs are turned off. The ITH pin is
then disconnected from the output of the EA and parked
at 0.450V.
In sleep mode, much of the internal circuitry is turned off,
reducing the quiescent current that the LTC3890-1 draws.
If one channel is shut down and the other channel is in
sleep mode, the LTC3890-1 draws only 50μA of quiescent
current. If both channels are in sleep mode, the LTC3890-1
draws only 60μA of quiescent current. In sleep mode,
the load current is supplied by the output capacitor. As
the output voltage decreases, the EA’s output begins to
rise. When the output voltage drops enough, the ITH pin
is reconnected to the output of the EA, the sleep signal
goes low, and the controller resumes normal operation
by turning on the top external MOSFET on the next cycle
of the internal oscillator.
When a controller is enabled for Burst Mode operation,
the inductor current is not allowed to reverse. The reverse
current comparator, IR, turns off the bottom external
MOSFET just before the inductor current reaches zero,
12
CC
. To select pulse-skipping mode, tie the
CC
– 1.3V.
(Refer to the Functional Diagram)
preventing it from reversing and going negative. Thus,
the controller operates in discontinuous operation.
In forced continuous operation or clocked by an external
clock source to use the phase-locked loop (see Frequency
Selection and Phase-Locked Loop section), the induc-
tor current is allowed to reverse at light loads or under
large transient conditions. The peak inductor current
is determined by the voltage on the ITH pin, just as in
normal operation. In this mode, the effi ciency at light
loads is lower than in Burst Mode operation. However,
continuous operation has the advantage of lower output
voltage ripple and less interference to audio circuitry. In
forced continuous mode, the output ripple is independent
of load current.
When the PLLIN/MODE pin is connected for pulse skipping
mode, the LTC3890-1 operates in PWM pulse skipping
mode at light loads. In this mode, constant frequency
operation is maintained down to approximately 1% of
designed maximum output current. At very light loads, the
current comparator, ICMP, may remain tripped for several
cycles and force the external top MOSFET to stay off for
the same number of cycles (i.e., skipping pulses). The
inductor current is not allowed to reverse (discontinuous
operation). This mode, like forced continuous operation,
exhibits low output ripple as well as low audio noise and
reduced RF interference as compared to Burst Mode
operation. It provides higher low current effi ciency than
forced continuous mode, but not nearly as high as Burst
Mode operation.
Frequency Selection and Phase-Locked Loop
(FREQ and PLLIN/MODE Pins)
The selection of switching frequency is a trade-off between
effi ciency and component size. Low frequency operation
increases effi ciency by reducing MOSFET switching
losses, but requires larger inductance and/or capacitance
to maintain low output ripple voltage.
The switching frequency of the LTC3890-1’s controllers
can be selected using the FREQ pin.
38901f