LT6012 Linear Technology, LT6012 Datasheet
LT6012
Available stocks
Related parts for LT6012
LT6012 Summary of contents
Page 1
... The LT6011/LT6012 are specified at 5V and 15V supplies and from – The LT6011 (dual) is available in SO-8 and space saving 3mm 3mm DFN packages. The LT6012 (quad) is available in SO-14 and 16-pin SSOP packages. , LTC and LT are registered trademarks of Linear Technology Corporation. SoftSpan is a trademark of Linear Technology Corporation. ...
Page 2
... S8 PART MARKING S8 PACKAGE 6011 = 150 C, = 190 C/W JA 6011I 6011A 6011AI ORDER PART TOP VIEW NUMBER 16 OUT D 15 –IN D – – LT6012CGN +IN D LT6012IGN – LT6012ACGN 12 + LT6012AIGN – – 11 – OUT C GN PART MARKING 9 NC 6012 GN PACKAGE 6012I = 150 C, ...
Page 3
... – LT6011DD, LT6012GN – LT6011AS8, LT6011S8, LT6012AS,LT6012S LT6011ADD, LT6011DD,LT6012AGN, LT6012GN LT6011AS8, LT6011ADD, LT6012AS, LT6012AGN – LT6011S8, LT6011DD, LT6012S, LT6012GN – ...
Page 4
... LT6011S8, LT6012S – LT6011DD, LT6012GN – LT6011AS8, LT6011ADD, LT6012AS, LT6012AGN – LT6011S8, LT6011DD, LT6012S, LT6012GN – ...
Page 5
... T = – LT6011AS8, LT6011S8, LT6012AS, LT6012S LT6011ADD, LT6011DD, LT6012AGN, LT6012GN LT6011AS8, LT6011ADD, LT6012AS LT6012AGN – LT6011S8, LT6011DD, LT6012S, LT6012GN – LT6011AS8, LT6011ADD, LT6012AS, LT6012AGN – ...
Page 6
... Note 5: The LT6011C/LT6012C are guaranteed to meet the specified performance from and is designed, characterized and expected to meet specified performance from – but is not tested or QA sampled at these temperatures. The LT6011I/LT6012I are guaranteed to meet specified performance from – ...
Page 7
... 1kHz 1 UNBALANCED SOURCE RESISTORS 0.1 TOTAL NOISE 100 0.01 RESISTOR NOISE ONLY 0.001 0.0001 100 1k 10k 100k 1M SOURCE RESISTANCE ( ) LT6011/LT6012 Offset Voltage vs Input Common Mode Voltage 120 V = 15V S TYPICAL PART 100 – – ...
Page 8
... LT6011/LT6012 W U TYPICAL PERFOR A CE CHARACTERISTICS 0.01Hz to 1Hz Noise V = 15V 100 TIME (SEC) 6011 G10 Output Saturation Voltage vs Load Current (Output Low 5V 0 – 0.01 0.01 0 LOAD CURRENT (mA) ...
Page 9
... –120 C = 500pF 50pF L –160 –5 –200 –10 – 240 –15 –20 –280 1k 10k 100k FREQUENCY (Hz) LT6011/LT6012 CMRR vs Frequency 160 = 5V 140 120 100 5V 100 1k 10k FREQUENCY (Hz) ...
Page 10
... For example resistor in series with each input provides protection against 30V differential voltage. Input Common Mode Range The LT6011/LT6012 output is able to swing close to each power supply rail (rail-to-rail out), but the input stage is limited to operating between V ing this common mode range will cause the gain to drop to zero, however, no phase reversal will occur ...
Page 11
... Capacitive Loads The LT6011/LT6012 can drive capacitive loads up to 500pF in unity gain. The capacitive load driving capability increases as the amplifier is used in higher gain configurations. A small series resistance between the output and the load further increases the amount of capacitance that the amplifier can drive ...
Page 12
... LT6011/LT6012 PACKAGE DESCRIPTIO 3.5 0.05 1.65 0.05 2.15 0.05 (2 SIDES) 0.28 0.05 0.50 BSC 2.38 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 4 ...
Page 13
... TYP .016 – .050 .014 – .019 (0.406 – 1.270) (0.355 – 0.483) TYP INCHES (MILLIMETERS) LT6011/LT6012 .189 – .197 (4.801 – 5.004) NOTE .150 – .157 (3.810 – 3.988) NOTE 3 1 ...
Page 14
... LT6011/LT6012 PACKAGE DESCRIPTIO .050 BSC N .245 MIN .030 .005 TYP RECOMMENDED SOLDER PAD LAYOUT .010 – .020 45 (0.254 – 0.508) .008 – .010 (0.203 – 0.254) .016 – .050 (0.406 – 1.270) NOTE: INCHES 1. DIMENSIONS IN (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. ...
Page 15
... TYP .015 .004 45 .053 – .068 (0.38 0.10) (1.351 – 1.727) 0 – 8 TYP .008 – .012 (0.203 – 0.305) LT6011/LT6012 .189 – .196* (4.801 – 4.978) .009 (0.229 REF .150 – .157** (3.810 – 3.988) ...
Page 16
... LT6011/LT6012 U TYPICAL APPLICATIO LT1790-1. 7.87k 1% 100k 18V ~600 ~40mV/mT OUT RELATED PARTS PART NUMBER DESCRIPTION LT1112/LT1114 Dual/Quad Low Power, Picoamp Input Precision Op Amp LT1880 Rail-to-Rail Output, Picoamp Input Precision Op Amp LT1881/LT1882 Dual/Quad Rail-to-Rail Output, Picoamp Input Precision Op Amp ...