LTC4300A-3 LINER [Linear Technology], LTC4300A-3 Datasheet
LTC4300A-3
Available stocks
Related parts for LTC4300A-3
LTC4300A-3 Summary of contents
Page 1
... When driven to V ENABLE pin sets normal operation. The LTC4300A-3 is available in the MSOP and 3mm × 3mm DFN packages. , LTC and LT are registered trademarks of Linear Technology Corporation. ...
Page 2
... ABSOLUTE AXI U RATI GND .................................................... – 0 GND .................................................. – 0 CC2 SDAIN, SCLIN, SDAOUT, SCLOUT ................. – 0 ENABLE ......................................................... – 0 Operating Temperature Range LTC4300A-3C ......................................... 0°C to 70°C LTC4300A-3I ...................................... – 40°C to 85°C U PACKAGE/ORDER I FOR ATIO TOP VIEW CC2 CC SCLOUT ...
Page 3
... Note 4: Guaranteed by design, not subject to test. Note total capacitance of one bus line in pF. B voltage, as shown in CC LTC4300A-3 = 2.7V to 5.5V, unless otherwise noted. CC2 MIN TYP MAX 1 2 ● 0 100 175 0 400 10 ● ...
Page 4
... LTC4300A TYPICAL PERFOR A CE CHARACTERISTICS I vs Temperature CC 5.3 5 5.5V CC 5.1 5.0 4.9 4.8 4 2.7V CC 4.6 4.5 4.4 4.3 –50 – 100 TEMPERATURE (°C) 4300-3 G01 Connection Circuitry V 300 250 200 150 100 10,000 20,000 R PULLUP 4 Input–Output High to Low Propagation Delay vs Temperature 100 V = 2.7V CC ...
Page 5
... C busses. Connect pull-up resistors from SDAIN and SCLIN to this pin. Place a bypass capacitor of at least 0.01µF close to this pin for best results. Exposed Pad (Pin 9, DFN Package Only): Exposed Pad may by be left open or connected to device ground. LTC4300A this feature is unused, tie referenced, do not connect ...
Page 6
... LTC4300A-3 W BLOCK DIAGRA SLEW RATE DETECTOR SDAIN 6 CONNECT SLEW RATE DETECTOR SCLIN 3 CONNECT + – + 0.55V / CC – 0.45V CC 95µs UVLO DELAY, RISING ENABLE 5 ONLY 6 TM 2-Wire Bus Buffer and Hot Swap 2mA 2mA BACKPLANE-TO-CARD CONNECTION CONNECT 100k 1V PRECHARGE 100k ...
Page 7
... I/O card. Once the LTC4300A-3 comes out of UVLO, it assumes that SDAIN and SCLIN have been inserted into a live system and that SDAOUT and SCLOUT are being powered up at the same time as itself ...
Page 8
... These allow the user to choose weaker DC pull-up currents on the bus, reducing power consumption while still meet- ing system rise-time requirements. During positive bus transitions, the LTC4300A-3 switches in 2mA (typical) of current to quickly slew the SDA and SCL lines once their DC voltages exceed 0.6V. Using a general rule of 20pF of ...
Page 9
... CC SDA SCL ENA1 ENA2 Figure 3. The LTC4300A PCI Application Where All the Pins Have the Same Length. ENABLE Should be Held Low Until All Transients Associated with the Live Insertion Have Settled W U Live Insertion and Capacitance Buffering Application Figures 3 and 4 illustrate the usage of the LTC4300A-3 in applications that take advantage of both its Hot Swap con- trolling and capacitance buffering features ...
Page 10
... V CC SDA SCL ENA1 ENA2 Figure 4. The LTC4300A Custom Application. Making ENABLE the Shortest Pin Ensures that V and V Connect Before ENABLE is Allowed to Go High, Connecting the Card to the Backplane CC CC2 5V to 3.3V Level Translator and Power Supply Redundancy Systems requiring different supply voltages for the backplane side and the card side can use the LTC4300A-3, as shown in Figure 5 ...
Page 11
... MS8 Package 8-Lead Plastic MSOP (Reference LTC DWG # 05-08-1660) DETAIL “A” 0.254 (.010) 0° – 6° TYP GAUGE PLANE 0.53 ± 0.152 (.021 ± .006) DETAIL “A” 0.18 (.007) LTC4300A 0.115 TYP 5 3.00 ±0.10 1.65 ± 0.10 (4 SIDES) (2 SIDES) 4 0.25 ± 0.05 0.75 ±0.05 2.38 ±0.10 (2 SIDES) 0.00 – 0.05 BOTTOM VIEW— ...
Page 12
... V V SDAIN CC CC2 SDAOUT SCLIN SCLOUT LTC4300A-3 ENABLE GND Figure 3.3V Level Translator COMMENTS Low R : 35Ω Single-Ended/70Ω Differential, ON Expandable to 32 Single or 16 Differential Channels Precision 50µA ± 2.5% Tolerance Over Temperature, 4 Selectable SMBus Addresses, DAC Powers up at Zero or Midscale 8 Selectable Addresses/16-Channel Capability DNL < ...