PCA9512AD ETC1 [List of Unclassifed Manufacturers], PCA9512AD Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
PCA9512AD
Manufacturer Part Number
PCA9512AD
Description
Level shifting hot swappable I2C-bus and SMBus bus buffer
Manufacturer
ETC1 [List of Unclassifed Manufacturers]
Datasheet
1.PCA9512AD.pdf
(22 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PCA9512AD
Manufacturer:
NXP
Quantity:
6 700
Part Number:
PCA9512AD
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
PCA9512ADP
Manufacturer:
MICROCHIP
Quantity:
4 600
Part Number:
PCA9512ADP
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
PCA9512ADP@118
Manufacturer:
NXP
Quantity:
1 030
Company:
Part Number:
PCA9512ADPЈ¬118
Manufacturer:
NXP
Quantity:
1 690
Company:
Part Number:
PCA9512ADЈ¬118
Manufacturer:
NXP
Quantity:
5 000
Philips Semiconductors
PCA9512A_1
Product data sheet
14.4 Manual soldering
14.5 Package related soldering information
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 C
or 265 C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300 C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 seconds to 5 seconds between 270 C and 320 C.
Table 6:
[1]
[2]
[3]
Package
BGA, HTSSON..T
SSOP..T
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,
HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,
HVSON, SMS
PLCC
LQFP, QFP, TQFP
SSOP, TSSOP, VSO, VSSOP
CWQCCN..L
•
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45 angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026);
order a copy from your Philips Semiconductors sales office.
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal or
external package cracks may occur due to vaporization of the moisture in them (the so called popcorn
effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit
Packages; Section: Packing Methods .
These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no
account be processed through more than one soldering cycle or subjected to infrared reflow soldering with
peak temperature exceeding 217 C
body peak temperature must be kept as low as possible.
[5]
transport direction of the printed-circuit board.
, SO, SOJ
[3]
[1]
, TFBGA, VFBGA, XSON
Suitability of surface mount IC packages for wave and reflow soldering methods
[8]
, PMFP
[3]
, LBGA, LFBGA, SQFP,
[9]
Rev. 01 — 7 October 2005
, WQCCN..L
Level shifting hot swappable I
[8]
10 C measured in the atmosphere of the reflow oven. The package
Soldering method
Wave
not suitable
not suitable
suitable
not recommended
not recommended
not suitable
[4]
2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
C-bus and SMBus bus buffer
[5] [6]
[7]
PCA9512A
Reflow
suitable
suitable
suitable
suitable
suitable
not suitable
[2]
19 of 22