EP1K50 ALTERA [Altera Corporation], EP1K50 Datasheet - Page 13

no-image

EP1K50

Manufacturer Part Number
EP1K50
Description
1. Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Manufacturer
ALTERA [Altera Corporation]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
EP1K50F1256-2AA
Manufacturer:
ALTERA
Quantity:
6
Part Number:
EP1K50F1256-2N
Manufacturer:
ALTERA
0
Part Number:
EP1K50F1484-2
Manufacturer:
IQR
Quantity:
700
Part Number:
EP1K50FC256
Manufacturer:
ALTERA
Quantity:
319
Part Number:
EP1K50FC256
Manufacturer:
ALTERA
Quantity:
450
Part Number:
EP1K50FC256-1
Manufacturer:
ALTERA
Quantity:
1 831
Part Number:
EP1K50FC256-1
Manufacturer:
Altera
Quantity:
10 000
Part Number:
EP1K50FC256-1
Manufacturer:
ALTERA
0
Part Number:
EP1K50FC256-1
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Part Number:
EP1K50FC256-1N
Manufacturer:
Altera
Quantity:
10 000
Part Number:
EP1K50FC256-1N
Manufacturer:
ALTERA
0
Part Number:
EP1K50FC256-3
Manufacturer:
ALTERA
Quantity:
850
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
External Flash Interface
© December 2009 Altera Corporation
f
f
Table 1–5
enhanced configuration device.
Table 1–5. Enhanced Configuration Devices in PS Mode
For configuration schematics and more information about concurrent configurations,
refer to the appropriate FPGA family chapter in the
The enhanced configuration devices support external FPGA or processor access to its
flash memory. The unused portions of the flash memory can be used by the external
device to store code or data. This interface can also be used in systems that implement
remote configuration capabilities. Configuration data within a particular
configuration page can be updated via the external flash interface and the system
could be reconfigured with the new FPGA image. This interface is also useful to store
Nios boot code, application code, or both.
For more information about the Stratix remote configuration feature, refer to the
Remote System Configuration with Stratix & Stratix GX Devices
Device Handbook.
The address, data, and control ports of the flash memory are internally connected to
the enhanced configuration device controller and to external device pins. An external
source can drive these external device pins to access the flash memory when the flash
interface is available.
This external flash interface is a shared bus interface with the configuration controller
chip. The configuration controller is the primary bus master. Since there is no bus
arbitration support, the external device can only access the flash interface when the
controller has tri-stated its internal interface to the flash. Simultaneous access by the
controller and the external device will cause contention, and result in configuration
and programming failures.
Since the internal flash interface is directly connected to the external flash interface
pins, controller flash access cycles will toggle the external flash interface pins. The
external device must be able to tri-state its flash interface during these operations and
ignore transitions on the flash interface pins.
Passive serial mode
Multi-device passive
serial mode
Multi-device passive
serial mode
Multi-device passive
serial mode
Note to
(1) This is the number of valid DATA outputs for each configuration mode.
Mode Name
Table
summarizes the concurrent PS configuration modes supported in the
1–5:
Mode (n =)
1
2
4
8
(1)
DATA0
DATA[1..0]
DATA[3..0]
DATA[7..0]
Used Outputs
Configuration Handbook (Complete Two-Volume Set)
Configuration
DATA[7..1] drive low
DATA[7..2] drive low
DATA[7..4] drive low
chapter in the Stratix
Handbook.
Unused Outputs
1–13

Related parts for EP1K50