MPC8308CVMADDA FREESCALE [Freescale Semiconductor, Inc], MPC8308CVMADDA Datasheet - Page 3

• Manufacturer Part Number: MPC8308CVMADDA
• Description: MPC8308 PowerQUICC II Pro Processor Hardware Specification
• Manufacturer: FREESCALE [Freescale Semiconductor, Inc]

Local bus, DUART, system control and power management,
eSDHC, I
Miscellaneous and JTAG I/O voltage
SERDES PHY
eTSEC I/O Voltage
Input voltage
Storage temperature range
Notes:
1. Functional and tested operating conditions are given in
2. Caution: MV
3. Caution: OV
4. Caution: LV
5. (M, L, O)V
6. The max value of supply voltage should be selected based on the RGMII mode. The lower range applies to RGMII mode.
7. NV
8. LV
2.1.2
Table 2
the recommended and tested operating conditions. Proper device operation outside of these conditions is
not guaranteed.
Freescale Semiconductor
SerDes internal digital power
SerDes internal digital power
SerDes I/O digital power
SerDes analog power for PLL
functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause
permanent damage to the device.
power-on reset and power-down sequences.
power-on reset and power-down sequences.
reset and power-down sequences.
DD1
DD
here refers to NV
here refers to NV
2
provides the recommended operating conditions for the device. Note that the values in
C, USB, Interrupt, Ethernet management, SPI,
IN
Power Supply Voltage Specification
IN
and MV
IN
IN
must not exceed LV
DDR2 DRAM signals
DDR2 DRAM reference
eTSEC
Local bus, DUART, system control and power
management, eSDHC, I
Ethernet management, SPI, Miscellaneous
and JTAG I/O voltage
must not exceed NV
must not exceed GV
REF
Characteristic
MPC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 0
DDA
DDC
Characteristic
may overshoot/undershoot to a voltage and for a maximum duration as shown in
, NV
and LV
DDB
Table 1. Absolute Maximum Ratings
DD
Table 2. Recommended Operating Conditions
DD2
,NV
DD
DD
by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on
by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during
2
by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during
DDG
refers to NV
C, Interrupt,
, NV
DDH
, NV
DDF
Table
DDP_K
from the ball map
2. Absolute maximum ratings are stress ratings only, and
LV
from the ball map.
XCOREV
XPADV
SDAV
Symbol
DD1,
MV
NV
MV
OV
T
LV
STG
REF
DD
IN
LV
IN
IN
XCOREV
XCOREV
DD
DD
XPADV
DD2
DD
SDAV
Symbol
,
1
,
(continued)
DD
DD
DD
SS
–0.3 to (GV
–0.3 to (GV
–0.3 to (NV
–0.3 to (LV
–0.3 to 2.75 or
–0.3 to 1.26
Max Value
–0.3 to 3.6
–0.3 to 3.6
–55 to 150
Recommended Value
DD
DD
DD
DD
1.0 V ± 50 mV
1.0 V ± 50 mV
1.0 V ± 50 mV
+ 0.3)
+ 0.3)
+ 0.3)
+ 0.3)
0.0
Electrical Characteristics
Figure 2
Unit
°C
Table 2
V
V
V
V
V
V
V
1
Notes
4, 5,8
3, 5,7
Unit
2, 5
2, 5
6,8
V
V
V
V
—
—
7
are
3