ISL6117 INTERSIL [Intersil Corporation], ISL6117 Datasheet - Page 5

• Manufacturer Part Number: ISL6117
• Description: Power Distribution Controllers
• Manufacturer: INTERSIL [Intersil Corporation]

Electrical Specifications
Description and Operation
The members of this family are single power supply
distribution controllers for generic hot swap applications
across the +2.5V to +12V supply range. The ISL6115 is
targeted for +12V switching applications whereas the
ISL6116 is targeted for +5V, the ISL6117 for +3.3V and the
ISL6120 for +2.5V applications. Each IC has a hardwired
undervoltage (UV) threshold level approximately 17% lower
than the stated voltages.
These ICs feature a highly accurate programmable
overcurrent (OC) detecting comparator, programmable
current regulation (CR) with programmable time delay to latch
off, and programmable soft-start turn-on ramp all set with a
minimum of external passive components. The ICs also
include severe OC protection that immediately shuts down the
MOSFET switch should a rapid load current transient such as
a near dead short cause the CR Vth to exceed the
programmed level by 150mV. Additionally, the ICs have a UV
indicator and an OC latch indicator. The functionality of the
PGOOD feature is enabled once the IC is biased, monitoring
and reporting any UV condition on the ISEN pin.
Upon initial power up, the IC can either isolate the voltage
supply from the load by holding the external N-Channel
MOSFET switch off or apply the supply rail voltage directly to
the load for true hot swap capability. The PWRON pin must
be pulled low for the device to isolate the power supply from
the load by holding the external N-channel MOSFET off.
With the PWRON pin held high or floating the IC will be in
true hot swap mode. In both cases the IC turns on in a soft-
start mode protecting the supply rail from sudden in-rush
current.
At turn-on, the external gate capacitor of the N-Channel
MOSFET is charged with a 10μA current source resulting in
a programmable ramp (soft-start turn-on). The internal
ISL6115 charge pump supplies the gate drive for the 12V
supply switch driving that gate to ~V
three ICs the gate drive voltage is limited to the chip bias
voltage, VDD.
Load current passes through the external current sense
resistor. When the voltage across the sense resistor exceeds
the user programmed CR voltage threshold value, (see
Table 1 for R
nominal current regulation threshold voltage, V
CURRENT REGULATION DURATION/POWER GOOD
C
C
Current Limit Time-Out Threshold Voltage
Power Good Pull Down Current
TIM
TIM
Charging Current
Fault Pull-Up Current (Note 3)
ISET
PARAMETER
programming resistor value and resulting
5
V
DD
= 12V, T
DD
+5V, for the other
ISL6115, ISL6116, ISL6117, ISL6120
A
C
C
SYMBOL
= T
TIM
PG_Ipd
CR
TIM
J
_ichg0
) the
_Vth
= 0°C to +85°C, Unless Otherwise Specified
V
CTIM Voltage
V
CTIM
OUT
= 0.5V
= 0V
TEST CONDITIONS
controller enters its current regulation mode. At this time, the
time-out capacitor, on C
source and the controller enters the current limit time to latch-
off period. The length of the current limit time to latch-off
duration is set by the value of a single external capacitor (see
Table 2) for CTIM capacitor value and resulting nominal
current limited time out to latch-off duration placed from the
CTIM pin (pin 6) to ground. The programmed current level is
held until either the OC event passes or the time out period
expires. If the former is the case then the N-Channel
MOSFET is fully enhanced and the C
discharged. Once CTIM charges to 1.87V, signaling that the
time out period has expired an internal latch is set whereby
the FET gate is quickly pulled to 0V turning off the N-Channel
MOSFET switch, isolating the faulty load.
NOTE: Nominal Vth = R
NOTE: Nominal time-out period = C
This IC responds to a severe overcurrent load (defined as a
voltage across the sense resistor >150mV over the OC Vth set
point) by immediately driving the N-Channel MOSFET gate to
0V in about 10μs. The gate voltage is then slowly ramped up
turning on the N-Channel MOSFET to the programmed current
regulation level; this is the start of the time out period.
Upon a UV condition the PGOOD signal will pull low when
tied high through a resistor to the logic or VDD supply. This
pin is a UV fault indicator. For an OC latch off indication,
monitor CTIM, pin 6. This pin will rise rapidly from 1.9V to
VDD once the time out period expires.
See Figures 12 to 16 for waveforms relevant to text.
The IC is reset after an OC latch-off condition by a low level
on the PWRON pin and is turned on by the PWRON pin
being driven high.
C
TIM
0.022μF
0.047μF
CAPACITOR
R
0.1μF
ISET
4.99kΩ
2.5kΩ
10kΩ
750Ω
RESISTOR
(Continued)
ISET
NOMINAL CURRENT LIMITED PERIOD
TIM
TABLE 1.
TABLE 2.
x 20μA.
pin is charged with a 20μA current
MIN
1.3
16
-
-
TIM
x 93kΩ.
TIM
NOMINAL OC VTH
4.4ms
9.3ms
2ms
TYP
1.8
20
20
8
capacitor is
200mV
100mV
50mV
15mV
MAX UNITS
2.3
23
February 6, 2007
-
-
mA
mA
μA
V