ISL6333A INTERSIL [Intersil Corporation], ISL6333A Datasheet - Page 37
![no-image](/images/no-image-200.jpg)
ISL6333A
Manufacturer Part Number
ISL6333A
Description
Three-Phase Buck PWM Controller with Integrated MOSFET Drivers and Light Load Efficiency Enhancements for Intel VR11.1 Applications
Manufacturer
INTERSIL [Intersil Corporation]
Datasheet
1.ISL6333A.pdf
(40 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL6333ACRZ
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6333ACRZ-T
Manufacturer:
INFINEON/英飞凌
Quantity:
20 000
Company:
Part Number:
ISL6333AIRZ
Manufacturer:
Intersil
Quantity:
215
enough to handle the AC component of the current drawn by
the upper MOSFETs which is related to duty cycle and the
number of active phases.
For a three-phase design, use Figure 27 to determine the
input-capacitor RMS current requirement set by the duty
cycle, maximum sustained output current (I
of the peak-to-peak inductor current (I
Select a bulk capacitor with a ripple current rating which will
minimize the total number of input capacitors required to
support the RMS current calculated. The voltage rating of the
capacitors should also be at least 1.25x greater than the
maximum input voltage. Figures 28 and 29 provide the same
input RMS current information for two-phase and single-phase
designs respectively. Use the same approach for selecting
the bulk capacitor type and number.
FIGURE 27. NORMALIZED INPUT-CAPACITOR RMS
FIGURE 28. NORMALIZED INPUT-CAPACITOR RMS
0.3
0.2
0.1
0.3
0.2
0.1
0
0
0
0
I
I
I
I
I
L(P-P)
L(P-P)
L(P-P)
L(P-P)
L(P-P)
CURRENT FOR 3-PHASE CONVERTER
CURRENT FOR 2-PHASE CONVERTER
= 0
= 0.25 I
= 0
= 0.5 I
= 0.75 I
0.2
0.2
O
O
O
DUTY CYCLE (V
DUTY CYCLE (V
0.4
0.4
37
I
I
L(P-P)
L(P-P)
ISL6333, ISL6333A, ISL6333B, ISL6333C
0.6
0.6
IN/
IN/
L,(P-P)
= 0.5 I
= 0.75 I
V
V
O
O
)
)
O
O
O
) to I
), and the ratio
0.8
0.8
O
.
1.0
1.0
Low capacitance, high-frequency ceramic capacitors are
needed in addition to the input bulk capacitors to suppress
leading and falling edge voltage spikes. The spikes result from
the high current slew rate produced by the upper MOSFET
turn on and off. Select low ESL ceramic capacitors and place
one as close as possible to each upper MOSFET drain to
minimize board parasitics and maximize suppression.
Layout Considerations
MOSFETs switch very fast and efficiently. The speed with
which the current transitions from one device to another
causes voltage spikes across the interconnecting
impedances and parasitic circuit elements. These voltage
spikes can degrade efficiency, radiate noise into the circuit
and lead to device overvoltage stress. Careful component
selection, layout, and placement minimizes these voltage
spikes. Consider, as an example, the turnoff transition of the
upper PWM MOSFET. Prior to turnoff, the upper MOSFET
was carrying channel current. During the turnoff, current
stops flowing in the upper MOSFET and is picked up by the
lower MOSFET. Any inductance in the switched current path
generates a large voltage spike during the switching interval.
Careful component selection, tight layout of the critical
components, and short, wide circuit traces minimize the
magnitude of voltage spikes.
There are two sets of critical components in a DC/DC
converter using the ISL6333 family of controllers. The power
components are the most critical because they switch large
amounts of energy. Next are small signal components that
connect to sensitive nodes or supply critical bypassing
current and signal coupling.
FIGURE 29. NORMALIZED INPUT-CAPACITOR RMS
0.6
0.4
0.2
0
0
I
I
I
CURRENT FOR SINGLE-PHASE CONVERTER
L(P-P)
L(P-P)
L(P-P)
0.2
= 0
= 0.5 I
= 0.75 I
DUTY CYCLE (V
O
O
0.4
0.6
IN
/V
O
)
0.8
October 8, 2010
FN6520.3
1.0