QT110H QUANTUM [Quantum Research Group], QT110H Datasheet
QT110H
Related parts for QT110H
QT110H Summary of contents
Page 1
... Light switches Industrial panels The QT110 / QT110H charge-transfer (“QT’”) sensor chips are self-contained digital ICs used to implement near-proximity or touch sensors. They project sense fields through almost any dielectric, like glass, plastic, stone, ceramic, and wood. They can also turn small metal-bearing objects into intrinsic sensors, making them respond to proximity or touch ...
Page 2
... SNS1 and SNS2 to make the piezo (if installed) sound a short tone for 75ms immediately after detection, to act as an audible confirmation. Option pins allow the selection or alteration of several other special features and sensitivity. Figure 1-2 2-wire operation, self-powered (not QT110H) 3.5 - 5.5V CMOS 1K Twisted 1N4148 ...
Page 3
By implication it requires that the signal ground and the target object must both be coupled together in some manner for a capacitive sensor to operate properly. Note that there is no need to provide actual hardwired ground ...
Page 4
... ODE UTPUT The output of the device can respond mode, where the output is active-low (QT110) or active-high (QT110H) upon detection. The output will remain active for the duration of the Figure 2-1 Drift Compensation Signal Threshold R eference ...
Page 5
... CMOS input, by doing nothing or at most adding a small non-critical capacitor from Out to ground (Figure 2-6). 2.2.6 O The QT110’s output is active low (QT110) or active high (QT110H) and can source 1mA or sink 5mA of non-inductive current. 5 Figure 2-3 Damping Piezo Clicks with R +2 ...
Page 6
... Vcc, so that it lights when the sensor is active-low. If desired the LED can be connected from Out to ground, and driven on when the sensor is inactive, but only with less drive current (1mA). QT110H: This part is active-high works in reverse to that described above CIRCUIT GUIDELINES 3.1 SAMPLE CAPACITOR When used for most applications, the charge sampler Cs can be virtually any plastic film or good quality ceramic capacitor ...
Page 7
Vdd disturbances that will interfere with the acquisition process. This can usually be solved by adding a small extra load from Vdd to ground, such as 10K ohms, to provide a minimum load on the ...
Page 8
ABSOLUTE MAXIMUM SPECIFICATIONS Operating temp ...
Page 9
DC SPECIFICATIONS Vdd = 3. 10nF 470K 10pF, Gain = High Parameter Description V Guaranteed min Vdd DDL I Supply current DD V Supply turn-on slope DDS V Low input ...
Page 10
MECHANICAL SYMBOL Min a 6.096 A 7.62 M 9.017 m 7.62 Q 0.889 P 0.254 L 0.355 L1 1.397 F 2.489 R 3.048 r 0.381 S 3.048 7.62 x 8.128 Y 0.203 SYMBOL Min M 4.800 ...
Page 11
... ORDERING INFORMATION PART QT110-D QT110-IS QT110H-D QT110H-IS LQ TEMP RANGE PACKAGE 0 - 70C PDIP -40 - 85C SOIC 70C PDIP -40 - 85C SOIC-8 11 MARKING QT1 + 10 or QT110 QT1 + I or QT110-I QT1 +10H or QT110H QT1 + AI or QT110H-I QT110/110H R1.03/0604 ...
Page 12
Tel: +44 (0)23 8056 5600 Fax: +44 (0)23 80565600 The specifications set out in this document are subject to change without notice. All products sold and services supplied by QRG are subject to our Terms and Conditions of sale ...