HIP9021IB INTERSIL [Intersil Corporation], HIP9021IB Datasheet - Page 6
![no-image](/images/no-image-200.jpg)
HIP9021IB
Manufacturer Part Number
HIP9021IB
Description
Portable Battery Drive/Torque Controller for N-Channel MOSFETs in Motor Control Systems
Manufacturer
INTERSIL [Intersil Corporation]
Datasheet
1.HIP9021IB.pdf
(7 pages)
Functional Description
Oscillator
The Oscillator triangle waveform is generated by the charge
and discharge of a 1nF external capacitor connected to the
OSC pin. The OSC terminal has a source and sink drive from a
current mirror which delivers 25 A. The charge and discharge
of the external capacitor is controlled by 2 comparators which
compare respectively V
V
Gate Driver
The TRIGGER input signal is compared from the triangle
waveform of the oscillator to produce a square wave signal.
The duty cycle of the GATE drive signal is increased as the
TRIGGER input level increases. The output of the compara-
tor is then NANDed with a GATE Control signal which can
enable or disable the GATE output. The NAND gate output is
buffered to deliver 18mA typical GATE drive current.
Torque Effect
The triangle signal, after going through a divider, is also
compared with TRIGGER input level. This produces another
square wave of the same period but with a duty-cycle that is
smaller than the GATE by ~5%. This square wave is used to
enable the comparison between DRAIN and TORQUE
inputs while the MOSFET is conducting.
DD
TORQUE
FIGURE 3. DETAILED LOGIC DIAGRAM OF THE PORTABLE DRIVE/TORQUE CONTROLLER FOR N-CHANNEL POWER MOSFETS
1nF
TRIGGER
. The period of the triangle wave is nominally 200 s.
OSC
SHOWING THE DRAIN AND TORQUE, THE GATE CONTROL LOGIC AND THE TRIGGER (SPEED) CONTROL.
OSC
PULL
DOWN
with 2/3 V
OSC
200K
50K
DD
6K
2K
40K
2K
and V
OSC
V
-
+
DD
1.15V
LOAD
COMP
with 1/3
-
+
REF.
BIAS
+
-
Q1
+
-
DELAY
COMP
HIP9021
POR
6
150K
A torque effect condition exists when 80% of the DRAIN sig-
nal is higher than the TORQUE input level set voltage of the
potentiometer. During this time, the external delay capacitor of
3.3 F is charged through an internal 100K resistor. When the
voltage at the DELAY pin reaches 0.25 x V
is then set and the Gate Control (GC) signal shown in Figure
3 goes to low. The Output GATE drive signal is then disabled.
This situation remains even if the voltage on the DELAY pin
stays under 0.25 x V
At the same time, when the RS flip-flop is set, the external
capacitor at the DELAY pin is discharged via the nMOS
device, Q2 which is driven by the Q output of the flip-flop.
Power-On Reset (POR)
In reference to Figure 3, the power on of the chip will cause
the reset of the RS Gate Control flip-flop when Q1 is
switched low. As an initial condition, the Gate Control (GC)
signal is reset high. Since power on is the only way to reset
the RS flip-flop, a disabled GATE drive signal due to a torque
effect condition requires a switched (trigger) reset.
The POR (power on reset) threshold requires that V
than 2V to initiate a reset. The POR circuit is based on the
behavior of the voltage reference cell that produces a constant
1.15V (REF. BIAS) when V
biased, the Q1 drain voltage goes low to reset the input of the
RS flip-flop.
R
S
330K
Q
Q
100K
CONTROL
GATE
(GC)
DD
Q2
BUF
for a sustained period of time.
DD
is over 2V. When Q1 is forward
GATE
DELAY
DRAIN
3.3
15K
F
V
DD
BATT
, the RS flip-flop
POWER
MOSFET
MOTOR
DD
be less