HCPL-050L-060 HP [Agilent(Hewlett-Packard)], HCPL-050L-060 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
HCPL-050L-060
Manufacturer Part Number
HCPL-050L-060
Description
LVTTL/LVCMOS Compatible 3.3 V Optocouplers (1 Mb/s)
Manufacturer
HP [Agilent(Hewlett-Packard)]
Datasheet
1.HCPL-050L-060.pdf
(11 pages)
Package Characteristics
Over Recommended Temperature (T
Parameter
Input-Output
Momentary
Withstand
Voltage**
Input-Output
Resistance
Input-Output
Capacitance
*All typicals at T
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table (if applicable),
your equipment level safety specification or Agilent Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage," publication
number 5963-2203E.
Notes:
8
10. The frequency at which the AC output voltage is 3 dB below its mid-frequency value.
11. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Agilent guarantees a minimum CTR of 15%.
12. See Option 020 data sheet for more information.
13. Use of a 0.1 f bypass capacitor connected between pins 5 and 8 is recommended.
14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage
15. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage
16. This rating is equally validated by an equivalent AC proof test.
1. Derate linearly above 70˚C free-air temperature at a rate of 0.8 mA/˚C (8-Pin DIP).
2. Derate linearly above 70˚C free-air temperature at a rate of 1.6 mA/˚C (8-Pin DIP).
3. Derate linearly above 70˚C free-air temperature at a rate of 0.9 mW/˚C (8-Pin DIP).
4. Derate linearly above 70˚C free-air temperature at a rate of 2.0 mW/˚C (8-Pin DIP).
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, I
6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
8. The 1.9 k load represents 1 TTL unit load of 1.6 mA and the 5.6 mA k
9. The 4.1 k load represents 1 LSTTL unit load of 0.36 mA and 6.1 k
Derate linearly above 85˚C free-air temperature at a rate of 0.5 mA/˚C (SO-8).
Derate linearly above 85˚C free-air temperature at a rate of 1.0 mA/˚C (SO-8).
Derate linearly above 85˚C free-air temperature at a rate of 1.1 mW/˚C (SO-8).
Derate linearly above 85˚C free-air temperature at a rate of 2.3 mW/˚C (SO-8).
mode pulse signal, V
Logic Low level is the maximum tolerable (negative) dV
output will remain in a Logic Low state (i.e., V
detection current limit, I
Related Characteristics Table, if applicable.
detection current limit, I
Related Characteristics Table, if applicable.
A
= 25˚C.
Sym.
V
I
R
C
I-O
ISO
I-O
I-O
CM
, to assure that the output will remain in a Logic High state (i.e., V
I-O
I-O
SO-8
Device
8-Pin DIP
SO-8
8-Pin DIP
8-Pin DIP
SO-8
8-Pin DIP
5 A). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation
5 A). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation
A
= 0˚C to 70˚C) unless otherwise specified.
O
< 0.8 V).
Min.
3750
CM
/dt on the trailing edge of the common mode pulse signal, V
Typ.* Max.
10
0.6
12
pull-up resistor.
1
pull-up resistor.
Units
V rms
pF
A
O
O
> 2.0 V). Common mode transient immunity in a
, to the forward LED input current, I
Test Conditions
RH < 50%,
t = 1 min.,
T
45% RH, t = 5 s,
V
T
V
f = 1 MHz
CM
A
A
I-O
I-O
= 25˚C
= 25˚C
/dt on the leading edge of the common
= 3 kVdc,
= 500 Vdc
4500 V rms for 1 second (leakage
6000 V rms for 1 second (leakage
CM
, to assure that the
Fig.
F
, times 100.
Note
6, 14
6, 16
6
6