ADL5812-EVALZ AD [Analog Devices], ADL5812-EVALZ Datasheet - Page 24
![no-image](/images/no-image-200.jpg)
ADL5812-EVALZ
Manufacturer Part Number
ADL5812-EVALZ
Description
Dual High IP3, 700 MHz to 2800 MHz, Double Balanced, Passive Mixer, IF Amplifier, and Wideband LO Amplifier
Manufacturer
AD [Analog Devices]
Datasheet
1.ADL5812-EVALZ.pdf
(28 pages)
ADL5812
REGISTER STRUCTURE
Figure 61 illustrates the register map of the ADL5812. The
ADL5812
control bits to five. When set to 0, the MAIN ENB and DIV
ENB bits, DB7 and DB6, respectively, enable the part. By setting
one of these bits to 1, its channel is powered down. Either
channel can be powered down independently of the other. The
RFB IN CAP DAC and RFB OUT CAP DAC bits are used to
tune the RF balun. In most cases, they are tuned together with
the higher settings, 7, tuning for the low frequencies, and with
the lower settings, 0, tuning for the high frequencies. There are
times where it becomes advantageous to tune the input and
Table 11. Optimum Settings
RF Frequency (MHz)
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
VGS2 VGS1 VGS0
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
RESERVED
0
1
'
0
0
1
'
uses only Register 5. Because of this, set all of the
0
0
1
'
VGS2 VGS1 VGS0 LPF1 LPF0
LPF1 LPF0 LOW PASS FILTER SETTING
0
1
'
VGS
VGS SETTING
0
1
LO Frequency (MHz)
497
597
697
797
897
997
1097
1197
1297
1397
1497
1597
1697
1797
1897
1997
2097
2197
2297
2397
2497
2597
'
0
7
'
LPF
0
3
'
CDO2 CDO1 CDO0 RF BALUN OUTPUT TUNING
0
1
'
0
0
1
'
CDO2 DCDO1 CDO0
RFB OUT CAP DAC
VGS
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
0
1
'
Figure 61. ADL5812 Register Maps
Rev. 0 | Page 24 of 28
0
0
7
'
CDI2 CDI1 CDI0 RF BALUN INTPUT TUNING
LPF
3
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
1
1
3
1
1
2
0
1
'
CDI2
RFB IN CAP DAC
0
1
'
output of the RF balun separately and that ability is provided.
The LPF bits control the low-pass filter settings at the IF output.
The ability to tune the low-pass filter allows some trade-off
between gain, noise figure, and input IP3 with higher settings,
3, providing higher input IP3 at the cost of some gain and noise
figure and lower settings, 0, providing higher gain and lower NF
at the cost of lower input IP3. The VGS bits control the VGS
settings of the mixer core and allow further tuning of the device.
Table 11 lists the optimum settings characterized for each
frequency band. All register bits default to 0.
CDI1
0
1
'
CDI0
DB9
RFB OUT CAP DAC
7
7
4
3
7
7
7
7
5
6
5
5
5
4
4
3
3
3
2
2
2
1
DB8
0
MAIN
MEN
MEN
ENB
DB7
7
0
'
0
1
DEN
DIV
ENB
DB6
DEVICE DISABLED
DEVICE ENABLED
DEN DIVERSITY ENABLE
MAIN ENABLE
0
1
DB5
DEVICE DISABLED
DEVICE ENABLED
0
RESERVED
DB4
0
DB3
0
RFB IN CAP DAC
7
7
4
3
7
7
7
7
5
6
5
5
5
4
4
3
3
3
2
2
2
1
C3(1) C2(0) C1(1)
DB2
CONTROL BITS
DB1
DB0