AT27C800-10DC ATMEL [ATMEL Corporation], AT27C800-10DC Datasheet
AT27C800-10DC
Related parts for AT27C800-10DC
AT27C800-10DC Summary of contents
Page 1
... Commercial and Industrial Temperature Ranges Description The AT27C800 is a low-power, high performance 8,388,608-bit UV erasable program- mable read only memory (EPROM) organized as either 512K 1024K by 8 bits. It requires a single 5V power supply in normal read mode operation. Any word can be accessed in less than 100 ns, eliminating the need for speed-reducing WAIT states ...
Page 2
... The device features two-line control(CE,OE) to eliminate bus contention in high-speed systems. With high density 512K word or 1024K-bit storage capabil- ity, the AT27C800 allows firmware stored reli- ably and to be accessed by the system without the delays of mass storage media. ...
Page 3
Absolute Maximum Ratings* Temperature Under Bias ...................- +125 C Storage Temperature ........................- +150 C Voltage on Any Pin with with Respect to Ground.....................-2.0V to +7.0V Voltage on A9 with Respect to Ground .........................-2.0V to +14.0V V ...
Page 4
... 5.0 AT27C800 - 10% 5V Min Max 1.0 5.0 10 100 1.0 50 -0.6 0.8 2 0.5 CC 0.4 2 AT27C800 -10 -12 -15 Max Min Max Min Max 100 120 150 100 120 150 5.0 5.0 100 120 150 10% Units A A ...
Page 5
Byte-Wide Read Mode AC Waveforms Note: 1. BYTE Byte-Wide Read Mode AC Waveforms Note: 1. BYTE BYTE Transition AC Waveforms A0 - A18 A-1 BYTE ...
Page 6
... R F Pin Capaticance ( MHz OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27C800 6 (1) Typ Max Output Test Load Note 100 pF including jig capacitance ...
Page 7
... Programming Waveforms Notes: 1. The Input Timing reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27C800, a 0.1 F capacitor is required across V DC Programming Characteristics ± 5° 6.5 ± 0.25V Symbol Parameter I Input Load Current ...
Page 8
... Program Pulse width tolerance Atmel’s 27C800 Integrated Product Identification Code A0 015 Codes 07 Manufacturer 0 0 Device Type 1 1 AT27C800 8 = 13.0 ± 0.25V PP Test Conditions Input Rise and Fall Times: (10% to 90%) 20 ns. Input Pulse Levels: (2) Input Pulse Levels: 0.8V to 2.0V Input Timing Reference Level: ...
Page 9
Rapid Programming Algorithm pulse width is used to program. The address is set to the first location raised to 6.5V and BYTE raised to 13.0V. Each address is first programmed with one ...
Page 10
... Lead, 0.600" Wide, Plastic Dual Inline Package (PDIP) 44R 44 Lead, 0.525" Wide, Plastic Gull Wing Small Outline Package (SOIC/SOP) 48T 48 Lead, Plastic Thin Small Outline Package (TSOP AT27C800 10 Ordering Code Package AT27C800-10DC 42DW6 AT27C800-10PC 42P6 AT27C800-10RC 44R AT27C800-10TC 48T AT27C800-10DI ...