XC17512L XILINX [Xilinx, Inc], XC17512L Datasheet
![no-image](/images/no-image-200.jpg)
XC17512L
Available stocks
Related parts for XC17512L
XC17512L Summary of contents
Page 1
... Product Specification 0 5* Description The XC1701L, XC1701 and XC17512L serial configuration PROMs (SCPs) provide an easy-to-use, cost-effective method for storing Xilinx FPGA configuration bitstreams. When the FPGA is in master serial mode, it generates a configuration clock that drives the SCP. A short access time after the rising clock edge, data appears on the SCP DATA output pin that is connected to the FPGA DIN pin ...
Page 2
... XC1701L (3.3V), XC1701 (5.0V) and XC17512L (3.3V) Serial Configuration PROMs Pin Description DATA Data output, 3-stated when either are inactive. During programming, the DATA pin is I/O. Note that OE can be programmed to be either active High or active Low. CLK Each rising edge on the CLK input increments the internal address counter, if both CE and OE are active ...
Page 3
Controlling Serial PROMs Most connections between the FPGA device and the Serial PROM are simple and self-explanatory. • The DATA output(s) of the of the Serial PROM(s) drives the DIN input of the lead FPGA device. • The master FPGA ...
Page 4
... XC1701L (3.3V), XC1701 (5.0V) and XC17512L (3.3V) Serial Configuration PROMs * If Readback is Activated, a 3.3-k Resistor is Required in Series With M1 During Configuration the 3 Pull-Down Resistor Overcomes the Internal Pull-Up, but it Allows M2 to General- be User I/O. Purpose User I/O Pins RESET Figure 2: Master Serial Mode. The one-time-programmable Serial Configuration PROM supports automatic loading of confi ...
Page 5
Standby Mode The PROM enters a low-power standby mode whenever CE is asserted High. The output remains in a high imped- ance state regardless of the state of the OE input. Table 1: Truth Table for XC1700 Control Inputs Control ...
Page 6
... XC1701L (3.3V), XC1701 (5.0V) and XC17512L (3.3V) Serial Configuration PROMs XC1701 Absolute Maximum Ratings Symbol V Supply voltage relative to GND CC V Supply voltage relative to GND PP V Input voltage relative to GND IN V Voltage applied to 3-state output TS T Storage temperature (ambient) STG T Maximum soldering temperature ( 1/16 in.) ...
Page 7
... XC1701L/XC17512L Absolute Maximum Ratings Symbol V Supply voltage relative to GND CC V Supply voltage relative to GND PP V Input voltage with respect to GND IN V Voltage applied to 3-state output TS T Storage temperature (ambient) STG T Maximum soldering temperature ( 1/16 in.) SOL Note: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not implied ...
Page 8
... XC1701L (3.3V), XC1701 (5.0V) and XC17512L (3.3V) Serial Configuration PROMs AC Characteristics Over Operating Condition CE RESET/OE CLK DATA Symbol Data Delay Data Delay CLK to Data Delay CAC 4 T Data Hold From CE, OE, or CLK Data Float Delay ...
Page 9
... Guaranteed by design, not tested. 4. All AC parameters are measured with V December 10, 1997 (Version 1.1) CDF Last Bit T 14 OCE XC1701 Min 2 = 0.0 V and First Bit 15 T OOE T 14 OCE X3183 XC1701L XC17512L Units Max Min Max 5-9 ...
Page 10
... XC1701L (3.3V), XC1701 (5.0V) and XC17512L (3.3V) Serial Configuration PROMs Ordering Information XC1701L PC20 C Device Number XC1701L XC1701 Package Type XC17512L PD8 = 8-Pin Plastic DIP SO20 = 20-Pin Plastic Small-Outline Package PC20 = 20-Pin Plastic Leaded Chip Carrier Marking Information Due to the small size of the serial PROM package, the complete ordering part number cannot be marked on the package. ...