LT3012 LINER [Linear Technology], LT3012 Datasheet - Page 4

• Manufacturer Part Number: LT3012
• Description: 250mA, 4V to 80V Low Dropout Micropower Linear Regulator
• Manufacturer: LINER [Linear Technology]

LT3012
PARAMETER
Output Voltage Noise
ADJ Pin Bias Current
Shutdown Threshold
SHDN Pin Current (Note 8)
Quiescent Current in Shutdown
Ripple Rejection
Current Limit
Reverse Output Current (Note 9)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3012 is tested and specifi ed for these conditions with the
ADJ pin connected to the OUT pin.
Note 3: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specifi cation will not apply
for all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 4: To satisfy requirements for minimum input voltage, the LT3012
is tested and specifi ed for these conditions with an external resistor
divider (249k bottom, 649k top) for an output voltage of 4.5V. The external
resistor divider will add a 5μA DC load on the output.
Note 5: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specifi ed output current. In dropout, the
output voltage will be equal to (V
ELECTRICAL CHARACTERISTICS
The
4
l
denotes the specifi cations which apply over the –40°C to 140°C operating temperature range, otherwise specifi cations are at T
IN
– V
DROPOUT
CONDITIONS
C
(Note 7)
V
V
V
V
V
V
V
V
V
OUT
OUT
OUT
SHDN
SHDN
IN
IN
IN
IN
OUT
).
= 6V, V
= 7V(Avg), V
= 7V, V
= 4.75V, ΔV
= 10μF, I
= Off to On
= On to Off
= 1.24V, V
= 0V
= 6V
SHDN
OUT
LOAD
= 0V
OUT
IN
= 0V
RIPPLE
< 1.24V (Note 2)
= 200mA, BW = 10Hz to 100kHz
= –0.1V (Note 2)
= 0.5V
(LT3012H)
P-P
, f
RIPPLE
Note 6: GND pin current is tested with V
load. This means the device is tested while operating close to its dropout
region. This is the worst-case GND pin current. The GND pin current will
decrease slightly at higher input voltages.
Note 7: ADJ pin bias current fl ows into the ADJ pin.
Note 8: SHDN pin current fl ows out of the SHDN pin.
Note 9: Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current fl ows into the OUT
pin and out the GND pin.
Note 10: The LT3012E is guaranteed to meet performance specifi cations
from 0°C to 125°C operating junction temperature. Specifi cations over
the –40°C to 125°C operating junction temperature range are assured by
design, characterization and correlation with statistical process controls.
The LT3012H is tested to the LT3012H Electrical Characteristics table at
140°C operating junction temperature. High junction temperatures degrade
operating lifetimes. Operating lifetime is derated at junction temperatures
greater than 125°C.
Note 11: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C (LT3012E) or 140°C (LT3012H) when
overtemperature protection is active. Continuous operation above the
specifi ed maximum operating junction temperature may impair device
reliability.
= 120Hz, I
LOAD
= 200mA
l
l
l
MIN
200
IN
0.3
65
= 4.75V and a current source
TYP
100
400
1.3
0.8
0.3
0.1
30
75
12
1
MAX
100
25
2
2
1
5
J
= 25°C.
UNITS
μV
3012fd
RMS
mA
mA
nA
μA
μA
μA
dB
μA
V
V