HIP1011D_04 INTERSIL [Intersil Corporation], HIP1011D_04 Datasheet

HIP1011D_04

Manufacturer Part Number

HIP1011D_04

Description

Dual Slot PCI Hot Plug Controllers

Manufacturer

INTERSIL [Intersil Corporation]

Datasheet

1.HIP1011D_04.pdf (15 pages)

Current page: 1 of 15
Download datasheet (354Kb)

Dual Slot PCI Hot Plug Controllers

The HIP1011D, HIP1011E are the first ICs available for

independent control of two PCI Hot-Plug slots. The

HIP1011D has all the features and functionality of two single

PCI Hot-Plug slot controllers such as the HIP1011A but in

the same foot print area. Like the single slot HIP1011B, the

HIP1011E does not monitor output voltage nor respond to

undervoltage conditions.

The HIP1011D, HIP1011E are designed to be physically

placed in close proximity to two adjacent PCI slots thus

reducing layout complexity and placement costs in

assembly. The HIP1011D, HIP1011E provides independent

power control to each slot and the addition of discrete power

MOSFETs and a few passive components creates two

complete power control solutions. The IC integrates the

+12V and -12V current sensing switches for each slot.

Overcurrent (OC) protection is provided by sensing the

voltage across external current-sense resistors. In addition,

on-chip references are used to monitor the +5V, +3.3V and

+12V outputs for undervoltage (UV) conditions *. The two

PWRON inputs control the state of the switches, one each

for slot A and slot B outputs. During an OC condition on any

output, or a UV condition on the +5V, +3.3V or +12V outputs

*, a LOW (0V) is asserted on the associated FLTN output

and all associated switches are latched-off. The outputs

servicing the adjacent slot are unaffected.

The time to FLTN signal going LOW and MOSFET latch off

is user determined by a single capacitor from each FLTN pin

to ground. This added feature enables the HIP1011D,

HIP1011E to ignore system noise transients. The FLTN latch

is cleared when the PWRON input is toggled low again.

During initial power-up of the main VCC supply (+12V), the

PWRON input is inhibited from turning on the switches, and

the latch is held in the Reset state until the VCC input is

greater than 10V.

User programmability of the overcurrent threshold and turn-

on slew rate is provided. A resistor connected to the OCSET

pin programs the overcurrent threshold for both slots.

Capacitors connected to the gate pins set the turn-on rate.

* UV references do not apply to HIP1011E.

Data Sheet

1-888-INTERSIL or 321-724-7143

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

Features

• Independent Power Control of 2 PCI Slots

• Turn-Off Delay Time Adjustability

• Internal MOSFET Switches for +12V and -12V Outputs

• µP Interface for On/Off Control and Fault Reporting

• Adjustable Overcurrent Protection for All Eight Supplies

• Provides Fault Isolation

• Adjustable Turn-On Slew Rate

• Minimum Parts Count Solution

• No Charge Pump

• 100ns Response Time to Overcurrent

• Pb-Free Available (RoHS Compliant)

Applications

• PCI Hot-Plug

Ordering Information

Pinout

HIP1011DCA*

HIP1011DCAZA*

(See Note)

HIP1011ECA*

HIP1011ECAZA*

(See Note)

* Add “-T” suffix for tape and reel option.

NOTE: Intersil Pb-free products employ special Pb-free material sets; molding

compounds/die attach materials and 100% matte tin plate termination finish,

which are RoHS compliant and compatible with both SnPb and Pb-free

soldering operations. Intersil Pb-free products are MSL classified at Pb-free

peak reflow temperatures that meet or exceed the Pb-free requirements of

IPC/JEDEC J STD-020C.

November 18, 2004

PART NUMBER

All other trademarks mentioned are the property of their respective owners.

Intersil (and design) is a registered trademark of Intersil Americas Inc.

PWRON_2

PWRON_1

M12VO_2

M12VG_2

M12VG_1

M12VO_1

FLTN_2

12VG_2

12VO_2

12VO_1

12VG_1

FLTN_1

OCSET

HIP1011D, HIP1011E (SSOP)

VSS

HIP1011D, HIP1011E

RANGE (°C)

0 to 70

TEMP.

TOP VIEW

28 Ld SSOP

(Pb-free)

28 Ld SSOP

(Pb-free)

PACKAGE

M12VIN_2

3VISEN_2

3VS_2

5VISEN_2

5VS_2

3V5VG_2

12VIN_2

12VIN_1

3V5VG_1

5VS_1

5VISEN_1

3VS_1

3VISEN_1

M12VIN_1

FN4725.5

M28.15

DWG. #

PKG.

Related parts for HIP1011D_04

HIP1011D_04 Summary of contents

Page 1

Data Sheet Dual Slot PCI Hot Plug Controllers The HIP1011D, HIP1011E are the first ICs available for independent control of two PCI Hot-Plug slots. The HIP1011D has all the features and functionality of two single PCI Hot-Plug slot controllers ...

Page 2

Typical Application 12V -12V M12VIN_1 M12G_1 C1 M12VO_1 M12VIN_2 M12G_2 C2 M12VO_2 12VIN_1 12VG_1 C3 12VO_1 12VIN_2 12VG_2 C4 12VO_2 FROM PWRON_1 SYSTEM CONTROLLER PWRON_2 -12V 12V 2 HIP1011D, HIP1011E SLOT 1 HIP1011D, HIP1011E OCSET VSS FLTN_1 FLTN_2 OPT. OPT. ...

Page 3

Simplified Schematic (1/2 HIP1011D, HIP1011E) SET (LOW = FAULT) 12V IN 12V IN 12V IN 5V REF 5V ZENER REFERENCE 12V IN LOW WHEN 12V 12V IN POWER-ON RESET 12V IN 100µA V OCSET OCSET 12V IN PWRON GND 3 ...

Page 4

Pin Descriptions PIN NO. DESIGNATOR FUNCTION 15, 28 M12VIN -12V Input 4, 11 FLTN Fault Output 20, 23 3V5VG 3.3V/5V Gate Output 21, 22 12VIN 12V Input 16, 27 3VISEN 3.3V Current Sense 17, 26 3VS 3.3V Source 19, 24 ...

Page 5

Absolute Maximum Ratings 12VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 6

Electrical Specifications Nominal 5.0V and 3.3V Input Supply Voltages, 12V IN PARAMETER +12V SUPPLY CONTROL On Resistance of Internal PMOS Overcurrent Threshold Overcurrent Threshold 12V Undervoltage Trip Threshold Undervoltage Fault Response Time Gate Charge Current Turn-On Time (PWRON High to ...

Page 7

Introduction The HIP1011D and HIP1011E are the first dual PCI slot IC devices designed to provide control and protection of the four PCI power supplies independently to two PCI slots. Like the widely used HIP1011 this device complies with the ...

Page 8

TABLE 1. HOW TO DETERMINE +25c NOMINAL (±10%) I SUPPLY FOR EACH SUPPLY +3.3V I ((100µ )/11.5)/R OC OCSET +5.0V I ((100µ )/14.5)/R OC OCSET +12V I (100µ )/1 OC OCSET -12V I (100µA ...

Page 9

Typical Performance Curves 340 320 NMOS - 300 PMOS +12 r 280 260 TEMPERATURE (°C) FIGURE TEMPERATURE ON 10.59 10.57 ...

Page 10

Typical Performance Curves 1.5 1.25 VOCSET = 1.2V 1.0 0.75 VOCSET = 0.6V 0 TEMPERATURE (°C) FIGURE 10. +12V OVERCURRENT LEVEL vs TEMPERATURE 102 101 ...

Page 11

Using the HIP1011DEVAL1 Platform General and Biasing Information The HIP1011DEVAL1 platform (Figure 24) comes as a three part set consisting of 1 motherboard emulator and 2 load cards. This evaluation platform allows a designer to evaluate and modify the performance ...

Page 12

Typical Performance Curves SUPPLY CURRENT CH2 ENABLE 2 CH1 ENABLE 1 CH1 AND CH2 VOLTAGE (5V/DIV) CH3 CURRENT (2A/DIV) FIGURE 18. HIP1011DEVAL1 3.3V SUPPLY CURRENT AS EACH SLOT CONTROLLER TURNS ON INTO LOAD CARD VG FLTN VOLTAGE (2V/DIV) FIGURE 20. ...

Page 13

J3 M12VIN_1 -12V BUS M12G_1 C1 M12VO_1 J1 M12VIN_2 M12G_2 C2 M12VO_2 J4 12VIN_1 +12V BUS 12VG_1 C3 12VO_1 12VIN_2 12VG_2 C4 12VO_2 TP3 PWRON_1 PWRON_2 TP12 OCSET -12V 12V TABLE 4. HIP1011DEVAL1 BOARD COMPONENT LISTING COMPONENT DESIGNATOR ...

Page 14

TABLE 4. HIP1011DEVAL1 BOARD COMPONENT LISTING (Continued) COMPONENT DESIGNATOR COMPONENT NAME RL1 3.3V Load Board Resistor RL2 5.0V Load Board Resistor RL3 +12V Load Board Resistor RL4 -12V Load Board Resistor CL1, CL2 +3.3V and +5.0V Load Board Capacitors CL3, ...

Page 15

Shrink Small Outline Plastic Packages (SSOP) Quarter Size Outline Plastic Packages (QSOP) N INDEX 0.25(0.010) H AREA E - SEATING PLANE - -C- α 0.10(0.004) 0.17(0.007 ...

Related keywords

HIP1011D_04 datasheet
HIP1011D_04 data sheet
HIP1011D_04 pdf datasheet
HIP1011D_04 component
HIP1011D_04 part
HIP1011D_04 distributor
HIP1011D_04 RoHS
HIP1011D_04 datasheet download