X60008B-50_06 INTERSIL [Intersil Corporation], X60008B-50_06 Datasheet
X60008B-50_06
Related parts for X60008B-50_06
X60008B-50_06 Summary of contents
Page 1
... SCK Bus SDAT CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 All other trademarks mentioned are the property of their respective owners. X60008B-50 FN8141.1 • Smart sensors • Strain Gage Bridges • Threshold Detectors • Servo Systems * ...
Page 2
... X60008BIS8-50* X60008B I X60008BIS8Z-50* (Note) X60008B ZI50 *Add "T1" suffix for tape and reel. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020 ...
Page 3
... The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. = 0mA 0.001µF, T OUT OUT Conditions T = 25°C A X60008BIS8-50 (1) +5.5V ≤ V ≤ +8.0V IN 0mA ≤ I ≤ 10mA SOURCE -10mA ≤ I ≤ 0mA SINK T = 25° ...
Page 4
... TYPICAL PERFORMANCE CHARACTERISTIC CURVES (V = 6.5V 0mA 25°C unless otherwise specified) IN OUT A LINE REGULATION 350 300 250 200 150 100 Vin (V) 4 X60008B-50 5.0004 5.0003 -40°C 5.0002 25°C 5.0001 5.0000 85°C 4.9999 4.9998 4.9997 LOAD REGULATION 0.6 -40°C 0.5 0.4 25°C 0.3 85°C ...
Page 5
... TEMPERATURE (C) 10mA LOAD TRANSIENT RESPONSE C = .001µF L ∆I = -10mA IN 500µSEC/DIV 5 X60008B-50 0 -10 -20 -30 -40 -50 -60 -70 -80 +60C +85C 10mA LOAD TRANSIENT RESPONSE ∆I = +10mA IN 10mA LOAD TRANSIENT RESPONSE C = .1µF L ∆I ...
Page 6
... I = 0mA 25°C unless otherwise specified) IN OUT A 50µA LOAD TRANSIENT RESPONSE C = .001µF L ∆I = -50µA IN ∆I IN 100µSEC/DIV 6 X60008B-50 50µA LOAD TRANSIENT RESPONSE C = +50µA 50µA LOAD TRANSIENT RESPONSE C = .1µF L ∆I = -50µA IN ∆I = +50µA IN 1mSEC/DIV = .01µF L ∆I = -50µA IN ∆ ...
Page 7
... L ∆V ∆V = -500mV IN 500µSEC/DIV MINIMUM DIFFERENTIAL IN OUT vs. OUTPUT CURRENT 0.50 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0. OUTPUT CURRENT (mA) 7 X60008B-50 = +500mV IN = +500mV IN 500.0 +85C 400.0 +25C 300.0 -40C 200.0 100.0 0 -10 LINE TRANSIENT RESPONSE C = .001µF L ∆V ∆V = -500mV = +500mV IN IN 500µSEC/DIV LINE TRANSIENT RESPONSE C = .1µ ...
Page 8
... IN OUT 900 800 700 600 500 400 300 5 units representative of I range IN 200 100 0 5.5 6 6.5 7 7 X60008B-50 IN 700 600 500 400 300 200 100 0 8 8.5 9 TURN-ON TIME OUT ...
Page 9
... X60008B-50 Other reference devices consuming higher supply cur- rents will need to be disabled in between conversions to conserve battery capacity. Absolute accuracy will ...
Page 10
... Care should be taken in system design to include this delay before measurements or conver- sions are started. 10 X60008B-50 Figure 4. Temperature Coefficient The limits stated for temperature coefficient (tempco) are governed by the method of measurement. The ...
Page 11
... Temperature 11 X60008B-50 The tempco curve for the X60008 devices is generally flat (within 0.5ppm/°C typically) over the industrial tem- perature range (-40 to 85°C) with some inflection at the extreme temperatures. The combination of very low tempco performance a predictable tempco slope is 10ppm/° ...
Page 12
... TYPICAL APPLICATION CIRCUITS V IN ±5.0V Dual Output, High Accuracy Reference +5.3-9. -5.5V to -9.0V IN +5.3-9.0V V X60008-50 GND 12 X60008B-50 Precision 5V, 50mA Reference. = 6V- 200Ω 2N2905 V IN X60008-50 V OUT 0.009µF GND 0.1µF 10µ X60008-50 V OUT 0.001µF GND V IN X60008-50 V OUT 0.001µF GND ...
Page 13
... TYPICAL APPLICATION CIRCUITS R C 0.001 IN 5V Full Scale Low-Drift 10-bit Adjustable Voltage Source 5.3-9.0V 2-Wire Bus 13 X60008B-50 Negative Voltage Reference X60008- OUT GND C = 0.001µF OUT -5. 200 R Limits max load current 1 1 with R I -9V 0.1µF 10µ OUT X60008-50 GND .001µF ...
Page 14
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14 X60008B-50 D (N/2)+1 (N/2) ...