ICL8052ACDD INTERSIL [Intersil Corporation], ICL8052ACDD Datasheet - Page 5

• Manufacturer Part Number: ICL8052ACDD
• Description: 14-Bit/16-Bit, Microprocessor- Compatible, 2-Chip, A/D Converter
• Manufacturer: INTERSIL [Intersil Corporation]

Absolute Maximum Ratings
ICL8052, ICL8068
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V
Differential Input Voltage
Input Voltage (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V
Output Short Circuit Duration All Outputs (Note 3). . . . . . . Indefinite
ICL7104
V+ Supply (GND to V+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V
V++ to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32V
Positive Supply Voltage (GND to V++) . . . . . . . . . . . . . . . . . . . . 17V
Negative Supply Voltage (GND to V-). . . . . . . . . . . . . . . . . . . . .-17V
Analog Input Voltage (Pins 32 - 39)(Note 4). . . . . . . . . . . . V++ to V-
Digital Input Voltage
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . .0
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
ICL7104 Electrical Specifications
Clock Input, CLK 1
Comparator I/P, COMP IN (Note 6)
Inputs with Pulldown, MODE
Inputs with Pullups
SEN, R/H
LBEN, MBEN, HBEN, CE/LD (Note 7)
Input High Voltage, All Digital Inputs
Input Low Voltage, All Digital Inputs
Digital Outputs Three-Stated On,
LBEN, MBEN (16 Only), HBEN, CE/LD
BIT n, POL, OR (Note 8)
Digital Outputs Three-Stated Off
Bit n, POL, OR
Non Three-State Digital Output
1.
2. For supply voltages less than 15V, the absolute maximum input voltage is equal to the supply voltage.
3. Short circuit may be to ground or either supply. Rating applies to 70
4. Input voltages may exceed the supply voltages provided the input current is limited to 100 A.
5. Connecting any digital inputs or outputs to voltages greater than V+ or less than GND may cause destructive device latchup. For this
(8068) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30V
(8052) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V
(Pins 2 - 30) (Note 5) . . . . . . . . . . . . (GND - 0.3V) to (V+ + 0.3V)
reason it is recommended that the power supply to the ICL7104 be established before any inputs from sources not on that supply are
applied.
STTS
Clock 2
Clock 3 (-14 Only)
JA
is measured with the component mounted on an evaluation PC board in free air.
PARAMETER
ICL8052/ICL7104, ICL8068/ICL7104
V+ = +5V, V++ = +15V, V- = -15V, T
SYMBOL
o
C to 70
V
V
V
V
V
V
V
V
V
V
V
I
I
I
I
I
I
I
OL
IN
IN
IH
IH
OH
OH
OH
OH
OH
IL
IL
OL
OL
OL
OL
IH
IL
o
C
5-10
V
V
V
V
V
V
I
I
I
0
I
I
I
I
I
I
OL
OH
OH
OL
OH
OL
OH
OL
OH
IN
IN
IN
IN
IN
IN
Thermal Information
Thermal Resistance (Typical, Note 1)
Maximum Junction Temperature (Ceramic Package) . . . . . . . . . 175
Maximum Junction Temperature (Plastic Package) . . . . . . . . 150
Maximum Storage Temperature Range . . . . . . . . . .-65
Maximum Lead Temperature (Soldering, 10s) . . . . . . . . . . . . 300
o
= 320 A
V
= 1.6mA
= 3.2mA
= 1.6mA
C ambient temperature.
= +5V to 0V
= 0V to +5V
= +5V
= 0V
= +5V
= 0V
= -10 A
= -240 A
= -400 A
= -320 A
= -320 A
14 Ld PDIP Package . . . . . . . . . . . . . .
40 Ld PDIP Package . . . . . . . . . . . . . .
14 Ld CERDIP Package . . . . . . . . . . .
OUT
CONDITIONS
TEST
V+
A
= 25
o
C, f
CLOCK
MIN
-10
-10
-10
-30
2.5
2.4
-10
2.4
2.4
1
-
-
-
-
-
-
-
= 200kHz
2
TYP
0.001
0.27
0.001
0.27
0.01
0.01
2.0
1.5
4.5
3.5
0.3
3.3
0.5
4.5
3.5
-5
5
7
JA
100
MAX
(
+10
60
75
o
1.0
0.4
0.4
0.4
10
30
10
10
-1
30
C/W)
-
-
-
-
-
-
-
o
C to 150
JC
UNITS
N/A
N/A
V
V
V
V
V
V
V
V
V
V
V
(
20
A
A
A
A
A
A
A
o
C/W)
o
o
o
o
C
C
C
C