X5001V8IZ-2.7 INTERSIL [Intersil Corporation], X5001V8IZ-2.7 Datasheet
X5001V8IZ-2.7
Related parts for X5001V8IZ-2.7
X5001V8IZ-2.7 Summary of contents
Page 1
Data Sheet CPU Supervisor FEATURES • 200ms power-on reset delay • Low V detection and reset assertion CC —Five standard reset threshold voltages —Adjust low V reset threshold voltage using CC special programming sequence —Reset signal valid to V ...
Page 2
... X5001S8-2.7A X5001 AN X5001S8Z-2.7A X5001 ZAN (Note) X5001S8I-2.7A X5001 AP X5001S8IZ-2.7A X5001 ZAP (Note) X5001V8-2.7A 501 AN X5001V8Z-2.7A 5001 ANZ (Note) X5001V8I-2.7A 501 AP X5001V8IZ-2.7A 5001 APZ (Note) X5001PI X5001P I X5001PIZ (Note) X5001P ZI X5001S8 X5001 X5001S8Z (Note) X5001 Z X5001S8I X5001 I X5001S8IZ (Note) X5001 ZI 2 X5001 TEMP ...
Page 3
... Ordering Information (Continued) PART NUMBER PART MARKING X5001V8 501 X5001V8Z (Note) 5001 Z X5001V8I 501 I X5001V8IZ (Note) 5001 IZ X5001PI-4.5A X5001P AM X5001PIZ-4.5A X5001P ZAM (Note) X5001S8-4.5A X5001 AL X5001S8Z-4.5A X5001 ZAL (Note) X5001S8I-4.5A X5001 AM X5001S8IZ-4.5A X5001 ZAM (Note) X5001V8-4.5A 501 AL X5001V8Z-4.5A 5001 ALZ (Note) X5001V8I-4 ...
Page 4
PIN CONFIGURATION 8 Ld TSSOP RESET CS/WDI PIN DESCRIPTION Pin Pin (SOIC/PDIP) TSSOP Name 1 1 CS/WDI SCK ...
Page 5
PRINCIPLES OF OPERATION Power-on Reset Application of power to the X5001 activates a power- on reset circuit. This circuit goes active at 1V and pulls the RESET/RESET pin active. This signal prevents the system microprocessor from starting to operate with ...
Page 6
Figure 1. Sample V Reset Circuit TRIP V P Adjust V TRIP Adj. Run Figure 2. Set V Level Sequence (V TRIP SCK SI 03h Figure ...
Page 7
Figure 4. V Programming Sequence TRIP New V Applied = CC Old V Applied + Error CC SPI INTERFACE The device is designed to interface directly with the synchronous Serial Peripheral Interface (SPI) of many popular microcontroller families. The device ...
Page 8
Watchdog Timer Register Watchdog Timer Control Bits The watchdog timer control bits, WD select the watchdog time out period. These nonvola- tile bits are programmed with the set ...
Page 9
Figure 5. Read Watchdog Timer Setting SCK RWDT Instruction SI SO Figure 6. Enable Watchdog Change/Disable Watchdog Change Sequence CS SCK SI SO Figure 7. Write Watchdog Timer Sequence CS 0 SCK SI High ...
Page 10
Figure 8. Read Nonvolatile Status (Option 1) (Used to determine end of Watchdog Timer store operation SCK SI SO Figure 9. Read Nonvolatile Status (Option 2) (Used to determine end of Watchdog Timer store operation ...
Page 11
ABSOLUTE MAXIMUM RATINGS Temperature under bias ................... -65°C to +135°C Storage temperature ........................ -65°C to +150°C Voltage on any pin with respect to V ...................................... -1.0V to +7V SS D.C. output current ............................................... 5mA Lead temperature (soldering, 10s) .................... 300°C ...
Page 12
POWER-UP TIMING Symbol Parameter (2) t Power-up to read operation PUR (2) t Power-up to write operation PUW CAPACITANCE (T = +25° 1MHz Symbol (2) C Output capacitance (SO, RESET) OUT (2) C Input capacitance (SCK, ...
Page 13
Data Output Timing Symbol Parameter f Clock frequency SCK t Output disable time DIS t Output valid from clock low V t Output hold time HO (3) t Output rise time RO (3) t Output fall time FO Notes: (3) ...
Page 14
SYMBOL TABLE WAVEFORM INPUTS OUTPUTS Must be Will be steady steady May change Will change from LOW from LOW to HIGH to HIGH May change Will change from HIGH from HIGH to LOW to LOW Don’t Care: Changing: Changes State ...
Page 15
Figure 13. CS vs. RESET Timing CS RESET RESET Output Timing Symbol Parameter t Watchdog timeout period, WDO pulse width ...
Page 16
V Programming Parameters TRIP Parameter t V program enable voltage setup time VPS TRIP t V program enable voltage hold time VPH TRIP t V programming CS inactive time PCS TRIP t V setup time TSU TRIP t V hold ...
Page 17
V Supply Current vs. Temperature (I CC Watchdog Timer Watchdog Timer Watchdog Timer Off (V CC 0.55 0.35 -40C 25C Temp (c) V vs. Temperature (programmed at 25°C) TRIP 5.025 5.000 ...
Page 18
Small Outline Package Family (SO PIN #1 I.D. MARK 0.010 SEATING PLANE 0.004 C 0.010 MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) SYMBOL SO-8 SO-14 ...
Page 19
Plastic Dual-In-Line Packages (PDIP) D SEATING PLANE MDP0031 PLASTIC DUAL-IN-LINE PACKAGE SYMBOL PDIP8 PDIP14 A 0.210 0.210 A1 0.015 0.015 A2 0.130 0.130 b 0.018 0.018 b2 0.060 0.060 c 0.010 0.010 D 0.375 0.750 E 0.310 ...
Page 20
Thin Shrink Small Outline Plastic Packages (TSSOP) N INDEX 0.25(0.010) E AREA E1 - 0.05(0.002) SEATING PLANE - -C- α 0.10(0.004) 0.10(0.004 NOTES: 1. These package ...