HIP6004 Intersil Corporation, HIP6004 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
HIP6004
Manufacturer Part Number
HIP6004
Description
Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor
Manufacturer
Intersil Corporation
Datasheet
1.HIP6004.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HIP6004ACB
Manufacturer:
HARRIS
Quantity:
103
Company:
Part Number:
HIP6004ACB
Manufacturer:
LSI
Quantity:
66
Part Number:
HIP6004ACB
Manufacturer:
HAR
Quantity:
20 000
Company:
Part Number:
HIP6004ACB-T
Manufacturer:
HAS
Quantity:
1 000
Part Number:
HIP6004ACB-T
Manufacturer:
HARRIS
Quantity:
20 000
Part Number:
HIP6004BCB
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
HIP6004BCB-T
Manufacturer:
INTERSIL
Quantity:
20 000
case response time. With a +12V input, and output voltage
level equal to DACOUT, t
Input Capacitor Selection
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use small ceramic
capacitors for high frequency decoupling and bulk capacitors
to supply the current needed each time Q
the small ceramic capacitors physically close to the
MOSFETs and between the drain of Q
Q
The important parameters for the bulk input capacitor are the
voltage rating and the RMS current rating. For reliable
operation, select the bulk capacitor with voltage and current
ratings above the maximum input voltage and largest RMS
current required by the circuit. The capacitor voltage rating
should be at least 1.25 times greater than the maximum
input voltage and a voltage rating of 1.5 times is a
conservative guideline. The RMS current rating requirement
for the input capacitor of a buck regulator is approximately
1/2 the DC load current.
For a through hole design, several electrolytic capacitors
(Panasonic HFQ series or Nichicon PL series or Sanyo
MV-GX or equivalent) may be needed. For surface mount
designs, solid tantalum capacitors can be used, but caution
must be exercised with regard to the capacitor surge current
rating. These capacitors must be capable of handling the
surge-current at power-up. The TPS series available from
AVX, and the 593D series from Sprague are both surge
current tested.
MOSFET Selection/Considerations
The HIP6004A requires 2 N-Channel power MOSFETs.
These should be selected based upon r
requirements, and thermal management requirements.
In high-current applications, the MOSFET power dissipation,
package selection and heatsink are the dominant design
factors. The power dissipation includes two loss
components; conduction loss and switching loss. The
conduction losses are the largest component of power
dissipation for both the upper and the lower MOSFETs.
These losses are distributed between the two MOSFETs
according to duty factor (see the equations below). Only the
upper MOSFET has switching losses, since the Schottky
rectifier clamps the switching node before the synchronous
rectifier turns on. These equations assume linear voltage-
current transitions and do not adequately model power loss
due the reverse-recovery of the lower MOSFET’s body
diode. The gate-charge losses are dissipated by the
HIP6004A and don't heat the MOSFETs. However, large
gate-charge increases the switching interval, t
increases the upper MOSFET switching losses. Ensure that
both MOSFETs are within their maximum junction
temperature at high ambient temperature by calculating the
temperature rise according to package thermal-resistance
2
.
FALL
2-71
is the longest response time.
1
DS(ON)
and the source of
1
turns on. Place
SW
, gate supply
which
HIP6004A
specifications. A separate heatsink may be necessary
depending upon MOSFET power, package type, ambient
temperature and air flow.
Standard-gate MOSFETs are normally recommended for
use with the HIP6004A. However, logic-level gate MOSFETs
can be used under special circumstances. The input voltage,
upper gate drive level, and the MOSFET’s absolute gate-to-
source voltage rating determine whether logic-level
MOSFETs are appropriate.
Figure 9 shows the upper gate drive (BOOT pin) supplied by
a bootstrap circuit from V
develops a floating supply voltage referenced to the PHASE
pin. This supply is refreshed each cycle to a voltage of V
less the boot diode drop (V
turns on. Logic-level MOSFETs can only be used if the
MOSFET’s absolute gate-to-source voltage rating exceeds
the maximum voltage applied to V
Figure 10 shows the upper gate drive supplied by a direct
connection to V
converter systems where the main input voltage is +5V
or less. The peak upper gate-to-source voltage is
approximately V
power and +12V
of Q
and a logic-level MOSFET can be used for Q
absolute gate-to-source voltage rating exceeds the
maximum voltage applied to V
P
P
Where: D is the duty cycle = V
UPPER
LOWER
HIP6004A
+
-
FIGURE 9. UPPER GATE DRIVE - BOOTSTRAP OPTION
1
V
+12V
is 7V. A logic-level MOSFET is a good choice for Q
CC
t
F
SW
= Io
S
= Io
is the switching frequency.
is the switch ON time, and
2
2
x r
x r
CC
CC
DC
+ V
DS(ON)
GND
D
DS(ON)
BOOT
. This option should only be used in
BOOT
UGATE
PHASE
LGATE
PGND
D
less the input supply. For +5V main
for the bias, the gate-to-source voltage
-
CC
x D + 1
x (1 - D)
D
C
. The boot capacitor, C
) when the lower MOSFET, Q
BOOT
OUT
CC
2
CC
.
Io x V
Q1
Q2
/ V
+5V OR +12V
.
IN
IN
,
x t
D2
NOTE:
V
SW
NOTE:
V
G-S
2
G-S
if its
x F
V
BOOT
V
CC
S
CC
-V
DC
CC
D
2
1