ATTIny13-12PI ATMEL Corporation, ATTIny13-12PI Datasheet - Page 94
ATTIny13-12PI
Manufacturer Part Number
ATTIny13-12PI
Description
8-bit AVR Microcontroller with 1K Bytes In-System Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet
1.ATTINY13-12PI.pdf
(169 pages)
- Current page: 94 of 169
- Download datasheet (3Mb)
Software Break Points
Limitations of
debugWIRE
debugWIRE Related
Register in I/O Memory
debugWire Data Register –
DWDR
94
ATtiny13
•
•
debugWIRE supports Program memory Break Points by the AVR Break instruction. Set-
ting a Break Point in AVR Studio
memory. The instruction replaced by the BREAK instruction will be stored. When pro-
gram execution is continued, the stored instruction will be executed before continuing
from the Program memory. A break can be inserted manually by putting the BREAK
instruction in the program.
The Flash must be re-programmed each time a Break Point is changed. This is auto-
matically handled by AVR Studio through the debugWIRE interface. The use of Break
Points will therefore reduce the Flash Data retention. Devices used for debugging pur-
poses should not be shipped to end customers.
The debugWIRE communication pin (dW) is physically located on the same pin as
External Reset (RESET). An External Reset source is therefore not supported when the
debugWIRE is enabled.
The debugWIRE system accurately emulates all I/O functions when running at full
speed, i.e., when the program in the CPU is running. When the CPU is stopped, care
must be taken while accessing some of the I/O Registers via the debugger (AVR Stu-
dio). See the debugWIRE documentation for detailed description of the limitations.
A programmed DWEN Fuse enables some parts of the clock system to be running in all
sleep modes. This will increase the power consumption while in sleep. Thus, the DWEN
Fuse should be disabled when debugWire is not used.
The following section describes the registers used with the debugWire.
The DWDR Register provides a communication channel from the running program in
the MCU to the debugger. This register is only accessible by the debugWIRE and can
therefore not be used as a general purpose register in the normal operations.
Bit
Read/Write
Initial Value
Capacitors inserted on the RESET pin must be disconnected when using
debugWire.
All external reset sources must be disconnected.
R/W
7
0
R/W
6
0
R/W
5
0
®
will insert a BREAK instruction in the Program
R/W
4
0
DWDR[7:0]
R/W
3
0
R/W
2
0
R/W
1
0
R/W
0
0
2535B–AVR–01/04
DWDR
Related parts for ATTIny13-12PI
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller With 1k Bytes In-system Programmable Flash - Atmel Corporation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet: