HEDS-550X Agilent(Hewlett-Packard), HEDS-550X Datasheet
![no-image](/images/no-image-200.jpg)
HEDS-550X
Related parts for HEDS-550X
HEDS-550X Summary of contents
Page 1
... HEDM-5600, and HEDS-5600/ 5640 feature external mounting ears. The quadrature signals and the index pulse are accessed through HEDM-550X/560X HEDS-550X/554X HEDS-560X/564X five 0.025 inch square pins located on 0.1 inch centers. Standard resolutions between 96 and 1024 counts per revolution are presently available. Consult local Agilent sales representatives for other resolutions ...
Page 2
... HEDS-5500/5540, HEDM-5500 *Note: For the HEDS-5500 and HEDM-5500, Pin # Connect. For the HEDS-5540, Pin #2 is CH. I, the index output. HEDS-5600/5640, HEDM-5600 *Note: For the HEDS-5600 and HEDM-5600, Pin # Connect. For the HEDS-5640, Pin #2 is CH. I, the index output. 2 ...
Page 3
... The photodiode outputs are then fed through the signal processing circuitry resulting and B (also I and I in the HEDS-5540 and 5640). Comparators receive these signals and produce the final outputs for channels A and B. Due to this integrated phasing ...
Page 4
... B will lead channel A. ): The Index Pulse Width (P O number of electrical degrees that an index output is high during one full shaft rotation. This value is nominally 1/4 cycle. HEDS-55XX/56XX - 100 C - 100 OUT 1000 Hz ...
Page 5
... Parameter Temperature HEDS Series Temperature HEDM Series Supply Voltage Load Capacitance Count Frequency Shaft Perpendicularity Plus Axial Play (HEDS Series) Shaft Eccentricity Plus Radial Play (HEDS Series) Shaft Perpendicularity Plus Axial Play (HEDM Series) Shaft Eccentricity Plus Radial Play(HEDM Series) Note: The module performance is guaranteed to 100 kHz but can operate at higher frequencies. 2.7 k required for HEDS-5540 and 5640 ...
Page 6
... Parameter HEDS-5500 Supply Current HEDS-5600 High Level Output Voltage Low Level Output Voltage Rise Time Fall Time HEDS-5540 Supply Current HEDS-5640 High Level Output Voltage HEDM-5500 Low Level Output Voltage HEDM-5600 Rise Time Fall Time HEDM-5500 Supply Current HEDM-5600 High Level Output Voltage ...
Page 7
... The HEDS-55X5 and 56X5, HEDM-5505, 5605 provide an 8.9 mm (0.35 inch) diameter hole through the housing for longer motor shafts. See Ordering Information. 3. The HEDS-5540 and 5640 must be aligned using the aligning pins as specified in Figure 3, or using the alignment tool as shown in “Encoder Mounting and Assembly”. See also “Mounting Considerations.” ...
Page 8
... Figure 1. Pull-up Resistors on HEDS-5X40 Encoder Outputs. Mounting Considerations The HEDS-5540 and 5640 three channel encoders and the HEDM Series high resolution encoders must be aligned using the aligning pins as specified in Figure 3, or using the HEDS-8910 Alignment Tool as shown in Encoder Mounting and Assembly. ...
Page 9
Figure 4. Mounting with External Ears. 9 2.39 / 2.34 (0.096 / 0.092) 0.25 (0.010) X 45° CHAMFER 2 PLACES A Ø 0.15 (0.006) 0.8 (0.03) X 45° CHAMFER O A 0.05 (0.002) 11.10 / 10.94 (0.438 / 0.431) ...
Page 10
... Encoder Mounting and Assembly 1. For HEDS-5500 and 5600: Mount encoder base plate onto motor. Tighten screws step 2. 1a. For HEDS-5540, 5640 and HEDM-5500, 5600: Slip alignment tool onto motor shaft. With alignment tool in place, mount encoder baseplate onto motor as shown above. ...
Page 11
... HEDM-5X0X COUNTER HEDS–55XX CH HCTL-1100 HEDS-56XX CH. B MOTION OR CONTROL IC HEDM-5X0X Part Number 103686-4 640442-5 65039-032 with 4825X-000 term. HEDS-8902 (2 ch.) with 4-wire leads HEDS-8903 (3 ch.) with 5-wire leads 2695 series with 2759 series term. * HOST 2020 PROCESSOR HOST PROCESSOR 11 * N/A * ...
Page 12
... Outputs 5 - Standard Channel 6 - External Mounting Ears (Included with each order of HEDM-550X/560X two channel encoders) HEDS-5 Option Resolution (Cycles/Rev) Through Hole (HEDS-550X, 560X 2 Channel None CPR 5 - 8.9 mm (0.35 in CPR C - 100 CPR D - 192 CPR E - 200 CPR (HEDS-554X, 564X 3 Channel CPR ...