HIP0063AB Intersil Corporation, HIP0063AB Datasheet

HIP0063AB

Manufacturer Part Number

HIP0063AB

Description

Hex Low Side MOSFET Driver with Serial or Parallel Interface and Diagnostic Fault Control

Manufacturer

Intersil Corporation

Datasheet

1.HIP0063AB.pdf (8 pages)

Current page: 1 of 8
Download datasheet (62Kb)

PRELIMINARY

October 1995

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

http://www.intersil.com or 407-727-9207

Features

• Six Channel MOSFET Driver with Gate Drive

• Drain Monitor Provides Fault Detection and

• Output Voltage Zener Clamp. . . . . . . . . . 67V Typ

• 5V CMOS Logic Level Input Control

• V

• Output Supply/Load Short and Open

• Automatic Change to Low Duty Cycle Drive

• Fault Diagnostic Feedback via the SPI Bus

• Operating Temp Range . . . . . . . -40

Applications

• Automotive and Industrial Systems

• Control of Solenoids, Relays and Lamp Drivers

• Interface to Logic and P Controllers

• Robotic System Controller

Pinout

HPW01

HPW45

HLOS

Control by Serial (SPI) or Parallel Interface and

an Option for PWM Logic Switching Control

Voltage Clamp for Each Channel

- 5V V

- Turns Off Gate Drive for Low or Loss of V

- 5.5V to 17V Battery/System Level Power

- Over-Voltage Shutdown . . . . . . . . . . . . 35V Typ

Load/Ground Short Fault Detection

Mode When Output Short-to-Supply Detected

GND

SCK

PWR

P10

P11

P12

P13

P14

P15

Supply Monitor

Logic Level Power Supply

System Level Power Supply Management

HIP0063 SOIC

Logic Power Supply

TOP VIEW

PWR

Block Diagram

Intersil Corporation 1999

HPW01

HPW45

C to +125

HLOS

PI0-5

SCK

PWR

Parallel Interface and Diagnostic Fault Control

Hex Low Side MOSFET Driver with Serial or

OVSD

CONTROL

POR

SPI (SER.)

CONTROL

Description

The HIP0063 is a logic controlled, six channel Low Side Power Driver. As

shown in the Block Diagram, the outputs are controlled via the serial data

interface or, by user option, each output may be independently controlled

from the respective parallel input. In addition, PWM logic switching control

(HLOS) may be directly applied to channels 0 and 1 in parallel, or channels 4

and 5 in parallel.

Output fault conditions may be detected as an output load short to supply

when the output is ON or as an open load/ground short when the output is

OFF. If an over-current short exists at one output, gate drive goes to a low

duty cycle mode. It will remain in the low duty cycle mode until switched off or

the fault is cleared. Fault bits are sent to a fault register to indicate which

channel is at fault. The fault bits are indicated by a logic one and is internally

latched when CS goes low. A fault bit will return to zero when the fault disap-

pears. Either an 8-bit or 16-bit SPI communication mode may be used. Refer

to the application section for bit control information.

Over-voltage shutdown protection for all outputs will occur when V

MOSFET Supply) exceeds 35V typical. When V

is switched off. The input and gate control logic is fully function when the V

supply is greater than 4V typical. The HIP0063 has an internal drain-to-gate

zener which is used to voltage clamp the output drain-to-source voltage of the

MOSFET.

The HIP0063 is fabricated in a Power BiMOS IC process, and is intended for

use in automotive and other applications having a wide range of temperature

and electrical stress conditions. It is particularly well suited for MOSFET con-

trol in circuits driving lamps, displays, relays, and solenoids in applications

requiring low operating power.

Ordering Information

PWM

(6)

MUX

HIP0063AB

NUMBER

+5V

PART

S0-5

F0-5

PI0-5

CHANNEL#0 - (1 OF 6)

TEMPERATURE

-40

HIP0063

OVSD

C to +125

RANGE

HIP0063

POR

CONTROL

FAULT LOGIC

FAULT DATA

LOGIC

AND LATCH

GATE

TIME DELAY

28 Lead Plastic SOIC (W)

CONTROL

OSC AND

is less than 3.5V, gate drive

PACKAGE

File Number

GND

EXT POWER

MOSFET AND

TYP LOAD

(DRAIN

MONITOR

VOLT,V

(GATE DR.

VOLT.,V

PWR

(Battery/

)

PWR

4009

Related parts for HIP0063AB

HIP0063AB Summary of contents

Page 1

... C to +125 C and electrical stress conditions particularly well suited for MOSFET con- trol in circuits driving lamps, displays, relays, and solenoids in applications requiring low operating power. Ordering Information PART NUMBER HIP0063AB Block Diagram CHANNEL OVSD PWR V +5V CC POR ...

Page 2

S0 SI SPI SCK CS PARALLEL/ PI0 SERIAL IN, DATA SHIFT REG. LATCH CONTROL PARALLEL/ PI1 SERIAL IN, DATA SHIFT REG. LATCH CONTROL PARALLEL/ PI2 SERIAL IN, DATA SHIFT REG. LATCH CONTROL PARALLEL/ PI3 SERIAL IN, DATA SHIFT REG. LATCH ...

Page 3

Absolute Maximum Ratings Logic Supply Voltage -0. Max Quiescent Logic Supply Current, I ...

Page 4

Electrical Speciﬁcations V = 4.5V to 5.5V PARAMETERS GATE DRIVE OUTPUT Gate Drive Output Source Current Gate Drive Output Sink Current Gate Drive Rise Time with Load Output Turn-ON Delay, Rising Edge 10 ...

Page 5

Serial Peripheral Interface Timing PARAMETERS Clock Operating Frequency Clock Period Clock High Time Clock Low Time Falling Edge Rising Edge of SCK Falling Edge of SCK to Rising Edge SCK Setup Time SI ...

Page 6

Applications Input Control The application circuit for the HIP0063 is shown in Figure 1 while details of input control are shown in the block diagram. Gate control and diagnostic fault management are provided for each of six channels. Gate controlled ...

Page 7

If there is still a problem in verifying the data sent, a communication error and further diagnosis is required. If the 16- bit mode is used, the data sent in the ﬁrst byte should be the same as the ...

Page 8

... All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certiﬁcation. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or speciﬁcations at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use ...

Related keywords

HIP0063AB datasheet
HIP0063AB data sheet
HIP0063AB pdf datasheet
HIP0063AB component
HIP0063AB part
HIP0063AB distributor
HIP0063AB RoHS
HIP0063AB datasheet download