FTR-1419 FINISAR [Finisar Corporation.], FTR-1419 Datasheet
FTR-1419
Related parts for FTR-1419
FTR-1419 Summary of contents
Page 1
... Fully metallic enclosure for low EMI • Low power dissipation Finisar’s FTR-1419 Extended GBIC transceivers have a maximum fiber length of 40 km, and comply with GBIC Specification Revision 5.4 Gigabit Ethernet standard as specified in IEEE Std 802.3 Additional real time diagnostic functions are also available via the 2-wire serial bus specified for Module Definition “ ...
Page 2
... II. Electrical Power Interface Finisar FTR-1419 GBICs have an extended power supply voltage range of 3.15V to 5.5V as described in Table 2. They are compatible with both 5V and 3.3V systems. The GBIC specification calls for a range of only 4.75V to 5.25 volts. The 6V maximum voltage is not allowed for continuous operation, however, TX_FAULT and TX_DISABLE circuitry in Finisar GBICs will function at 6V ...
Page 3
... FTR-1419 40km Extended GBIC Product Specification – November 2007 Electrical Power Interface Parameter Symbol Supply Current I s Maximum Voltage V max Surge Current I surge Input Voltage V cc III. Low Speed Signals RX_LOS, TX_DISABLE, and TX_FAULT are TTL signals as described in Table 3. MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA) are open drain CMOS signals (see section VI, “ ...
Page 4
... FTR-1419 40km Extended GBIC Product Specification – November 2007 Low Speed Signal Parameters Parameter Symbol Min RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay t_loss_on RX_LOS Negate Delay t_loss_off TX_DISABLE Assert Time t_off TX_DISABLE Negate Time t_on TX_DISABLE Reset Time ...
Page 5
... FTR-1419 40km Extended GBIC Product Specification – November 2007 V. Optical Parameters Optical Parameters Parameter Transmitter Center Wavelength Side Mode Suppression Ratio (SMSR) Transmitter Optical Output Power Transmitter Extinction Ratio Transmitter Eye Opening Optical Rise / Fall Time Optical Input Wavelength Total Transmitter Jitter ...
Page 6
... FTR-1419 40km Extended GBIC Product Specification – November 2007 VII. Environmental Specifications The GBIC Standard requires an ambient temperature range of 0°C to +50°C. Finisar FTR-1419 GBICs have an extended range from 0°C to +70°C case temperature as specified in Table 8. Environment Parameter Symbol Min ...
Page 7
... FTR-1419 40km Extended GBIC Product Specification – November 2007 Timing Requirements Parameter Symbol 2 Atmel I C Clock Rate C atmel Finisar Microcontroller Clock Rate Finisar Microcontroller Clock Rate © Finisar Corporation November 16, 2007 Rev.G1 Min Typ Max Units Notes/Conditions ...
Page 8
... FTR-1419 40km Extended GBIC Product Specification – November 2007 IX. Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5.4, Section 6 Insertion, Extraction, and Retention Forces Parameter Symbol Min GBIC insertion GBIC extraction GBIC retention ...
Page 9
... Serial CMOS E www.Atmel.com * The GBIC Standard, FC-PI and IEEE 802.3 do not specify a 1310nm single-mode interface for 40km applications. The FTR-1419 complies with these standards except for the following optical parameters: extinction ratio, receiver sensitivity and transmit output power. See Table 6 for details. ...