MT90823AP MITEL [Mitel Networks Corporation], MT90823AP Datasheet - Page 10

• Manufacturer Part Number: MT90823AP
• Description: 3V Large Digital Switch
• Manufacturer: MITEL [Mitel Networks Corporation]

MT90823
delay to ensure minimum delay between input and
output data. In wideband data applications, select
constant throughput delay to maintain the frame
integrity of the information through the switch.
The delay through the device varies according to the
type of throughput delay selected in the V/C bit of the
connection memory.
Variable Delay Mode (V/C bit = 0)
The delay in this mode is dependent only on the
combination of source and destination channels. It is
independent of input and output streams. The
minimum delay achievable in the MT90823 is three
time-slots. When the input channel data is switched
to the same output channel (channel n, frame p), it
will be output in the following frame (channel n,
frame p+1). The same frame delay occurs if the input
channel n is switched to output channel n+1 or n+2.
When input channel n is switched to output channel
n+3, n+4,..., the new output data will appear in the
same frame. Table 2 shows the possible delays for
the MT90823 in the variable delay mode.
Constant Delay Mode (V/C bit = 1)
In this mode, frame integrity is maintained in all
switching configurations by using a multiple data
memory buffer. Input channel data written into the
data memory buffers during frame n will be read out
during frame n+2.
10
Input Rate
2.048 Mb/s
4.096 Mb/s
8.192 Mb/s
CMOS
Input Rate
2.048 Mb/s
4.096 Mb/s
8.192 Mb/s
128 - (n-m) time-slots
32 - (n-m) time-slots
64 - (n-m) time-slots
Table 3 - Constant Throughput Delay Value
Table 2 - Variable Throughput Delay Value
m < n
Delay for Variable Throughput Delay Mode
(m - output channel number)
(n - input channel number))
In the MT90823, the minimum throughput delay
achievable in the constant delay mode is one frame.
For example, in 2 Mb/s mode, when input time-slot
31 is switched to output time-slot 0. The maximum
delay of 94 time-slots occurs when time-slot 0 in a
frame is switched to time-slot 31 in the frame. See
Table 3.
Microprocessor Interface
The MT90823 provides a parallel microprocessor
interface for non-multiplexed or multiplexed bus
structures. This interface is compatible with Motorola
non-multiplexed and multiplexed buses.
If the IM pin is low, the MT90823 microprocessor
interface assumes Motorola non-multiplexed bus
mode. If the IM pin is high, the device micro-
processor interface accepts two different timing
modes (mode1 and mode2) which allows direct
connection to multiplexed microprocessors.
The microprocessor interface automatically identifies
the type of microprocessor bus connected to the
MT90823. This circuit uses the level of the DS/RD
input pin at the rising edge of AS/ALE to identify the
appropriate bus timing connected to the MT90823. If
DS/RD is high at the falling edge of AS/ALE, then the
mode 1 multiplexed timing is selected. If DS/RD is
low at the falling edge of AS/ALE, then the mode 2
multiplexed bus timing is selected.
m-n + 128 time-slots
m-n + 32 time-slots
m-n + 64 time-slots
Delay for Constant Throughput Delay Mode
m = n, n+1, n+2
128 + (128 - n) + (m- 1) time-slots
32 + (32 - n) + (m - 1) time-slots
64 + (64 - n) + (m- 1) time-slots
(m - output channel number)
(n - input channel number))
m-n time-slots
m-n time-slots
m-n time-slots
m > n+2