XE0092LCC ETC1 [List of Unclassifed Manufacturers], XE0092LCC Datasheet
XE0092LCC
Related parts for XE0092LCC
XE0092LCC Summary of contents
Page 1
Xecom XE24S500 the Smallest, Complete 2.4 GHZ FHSS Transceiver Description The Xecom XE24S500 is a miniature 2.4 GHz Spread Spectrum transceiver. It includes all RF hardware and a micro-controller to manage the communications link. The micro-controller manages all communications task ...
Page 2
XE24S500 MECHANICAL SPECIFICATIONS 18 0.100” 10 XECOM 0.100” 1 bottom 9 (2) XE24S500 ...
Page 3
Using the XE24S500 Power Saving Modes The XE24S500 includes three low power operating modes (Sleep, Power-Down and RF Monitor) to allow the host application to make maximum use of the available power. The #P command selects the transceiver operating mode ...
Page 4
XE24S500 PIN CONFIGURATION SIGNAL PINS DESCRIPTION DIO2 1 DIO2 may be programmed as either a digital input or digital output. It connects directly to the communications controller in the XE24S500. DIO3 2 DIO3 may be programmed as either a digital ...
Page 5
ABSOLUTE MAXIMUM RATINGS Operating Temperature Range WARNING: Exceeding any of these ratings will void the warranty and may damage the device XE24S500 ELECTRICAL SPECIFICATIONS Parameter VCC ICC Output Power: Wireless Receive Sensitivity Range thru Physical Obstructions Frequency Hopping Channels Frequency ...
Page 6
XE24S500 TYPICAL CONNECTION DIAGRAM Host Serial I/F Parts List for XE24S500 Typical Connection Diagram Reference Designation C1 C2 Antenna * XECOM 3 DIO2 DIO3 L1 VCC /RTS /CTS RXD TXD ...
Page 7
XE24S500 COMMUNICATIONS CONTROLLER An internal micro-controller serves as the XE24S500 communications controller. This micro-controller manages the host interface, manages the wireless link, and formats data for the RF communications. HOST INTERFACE The XE24S500 has two primary system interfaces; the serial ...
Page 8
XE24S500 COMMUNICATIONS CONTROLLER (continued) Configuring for Sensor Operation ™ All SensorOnAir functions are performed by the XE24S500 communications controller. Modem-like AT commands loaded through the serial interface, program the functions of the analog and digital lines. The configuration is then ...
Page 9
XE24S COMMUNICATIONS CONTROLLER (continued) Sample File Transfer Transmitter TXD RXD AT#T01<cr> :<cr> abc...z 3 sec pause in data Note: In the above example that the file transfer is assumed to be completed when three seconds pass with no data being ...
Page 10
XE24S500 COMMUNICATIONS CONTROLLER (continued) USER CODE The Texas Instruments MSP430F148 microcontroller serves as the communications controller in the XE24S500 transceiver modules; however, the communications functions do not fully utilize the capabilities of the microcontroller. Xecom has created a way for ...
Page 11
AT COMMANDS An asterisk indicates the factory default A Answer Command - force response to a link request Dn Initiate a Wireless Link - attempt to connect with the transceiver at address n. En Echo Characters - n=0 Characters not ...
Page 12
AT COMMANDS #IxxxAn? Read Analog Input “n” at Node Address xxx - allows analog input values at any node to be read remotely. n=0 Read input ADC0 n=1 Read input ADC1 #IxxxDn? Read Digital Input “n” at Node Address xxx ...
Page 13
XE24S Configuration Registers S0 Answer Wireless Link Request: S0 determines if the XE24S500 automatically responds to a wireless link request. S0=0 No response to link requests S0=1 Automatically respond to link request S0=128 Enter Broadcast mode on power- up. The ...
Page 14
XE24S Configuration Registers S107 I/O Configuration - S107 is a bit-mapped register which defines the local I/O lines. Bit 0 =0 ADC0 and ADC1 defined as digital I/O =1 ADC0 and ADC1 defined as Analog inputs Bit 1 = reserved ...
Page 15
FCC PART 15 REGULATIONS Mounting the XE24S500 in Your Assembly The XE24S500 must be mounted horizontally on your printed circuit board to maintain proper orientation of the transceiver. Standoffs should also be used on the side opposite the pin row ...
Page 16
Terms of Sale Devices sold by XECOM are covered by the warranty provisions appearing in its Terms of Sale only. XECOM makes no war- ranty, express, statutory, implied description regarding the information set forth herein, or regarding the ...