PEEL16CV8 ANACHIP [Anachip Corp], PEEL16CV8 Datasheet - Page 4

• Manufacturer Part Number: PEEL16CV8
• Description: CMOS Programmable Electrically Erasable Logic Device
• Manufacturer: ANACHIP [Anachip Corp]

Anachip Corp.
www.anachip.com.tw
Complex Mode
In Complex mode, seven product terms feed the OR array which can
generate a purely combinatorial function for the output pin. The pro-
grammable output polarity selector provides active-high or active-low
logic, eliminating the need for external inverters. The output buffer is
controlled by the eighth product term, allowing the macrocell to be con-
figured for input, output, or bidirectional functions. Feedback into the
array for input or bidirectional functions is available on all pins except 12
and 19. Figure 4 shows the possible complex mode macrocell configura-
tions.
Figure 4 - Macrocell Configurations for the Complex Mode of the
Registered Mode
Registered mode provides eight product terms to the OR array for regis-
tered functions. The programmable output polarity selector provides
active-high or active-low logic, eliminating the need for external invert-
ers. (Note, however, that if register is selected, the PEEL
gisters power-up reset and so before the first clock arrives the output at
the pin will be low if the user has selected active-high logic and high if the
user has selected active-low logic. If combinatorial is selected, the output
will be a function of the logic.) For registered functions, the output buffer
enable is controlled directly from the /OE control pin. Feedback into the
array comes from the macrocell register. In Registered mode, input pins
1 and 11 are permanently allocated as CLK and /OE, respec- tively. Figure
8 shows the logic array of the PEEL
mode.
Registered mode also provides the option of configuring a macrocell for
combinatorial operation, with seven product terms feeding the OR func-
tion.
Again the programmable output polarity selector provides active-high or
active-low logic. The output buffer enable is controlled by the eighth
product term, allowing the macrocell to be configured for input, output, or
bidirectional functions. Feedback into the array for input or bidirectional
functions is available on all I/O pins. Macrocell Configurations for the
Registered Mode of the PEEL
PEEL
1
TM
Complex Mode
Active Low Output
16CV8 (see Figure 7 for Logic Array)
PRODUCT TERM
TM
16CV8
2
TM
Complex Mode
Active High Output
16CV8 configured in Registered
PRODUCT TERM
TM
16CV8 reg-
4/11
Figure 5 - Macrocell Configurations for the Registered Mode of the
PEEL
Design Security
The PEEL
vents unauthorized reading or copying of designs programmed into the
device. The security bit is set by the PLD programmer, either at the con-
clusion of the programming cycle or as a separate step, after the device
has been programmed. Once the security bit has been set it is impossi-
ble to verify (read) or program the PEEL
been erased with the bulk-erase function.
Signature Word
The signature word feature allows a 64-bit code to be programmed into
the PEEL
has been set. The signature word can be used to identify the pattern
programmed into the device or to record the design revision, etc.
1 Registered Mode
3 Registered Mode
TM
Active Low Registered Output
Active Low Combinatorial Output
16CV8 (see Figure 8 for logic Array)
OE PIN
CLK PIN
TM
TM
PRODUCT TERM
16CV8. The code cannot be read back after the security bit
16CV8 provides a special EEPROM security bit that pre-
D
Q
Q
4 Registered Mode
2
Registered Mode
Active High Registered Output
Active High Combinatorial Output
TM
OE PIN
CLK PIN
PRODUCT TERM
until the entire device has first
D
Rev. 1.0 Dec 16, 2004
Q
Q