KMM366S1623CT-G8 SAMSUNG [Samsung semiconductor], KMM366S1623CT-G8 Datasheet
KMM366S1623CT-G8
Related parts for KMM366S1623CT-G8
KMM366S1623CT-G8 Summary of contents
Page 1
... DQM4 140 DQ49 168 DD Preliminary PC100 SDRAM MODULE Part No. Max Freq. (Speed) KMM366S1623CT-G8 125MHz (8ns @ CL=3) KMM366S1623CT-GH 100MHz (10ns @ CL=2) KMM366S1623CT-GL 100MHz (10ns @ CL=3) 0.3V power supply Latency (Access from column address) Burst length ( & Full page) Data scramble (Sequential & Interleave) ...
Page 2
... KMM366S1623CT PIN CONFIGURATION DESCRIPTION Pin Name CLK System clock CS Chip select CKE Clock enable A0 ~ A11 Address BA0 ~ BA1 Bank select address RAS Row address strobe CAS Column address strobe WE Write enable DQM0 ~ 7 Data input/output mask DQ0 ~ 63 Data input/output WP Write protection V /V Power supply/ground ...
Page 3
... KMM366S1623CT FUNCTIONAL BLOCK DIAGRAM CS1 CS0 DQM0 DQM CS DQ0 DQ0 DQ1 DQ1 DQ2 DQ2 U0 DQ3 DQ3 DQ4 DQ4 DQ5 DQ5 DQ6 DQ6 DQ7 DQ7 DQM1 DQM CS DQ8 DQ0 DQ9 DQ1 DQ10 DQ2 U1 DQ11 DQ3 DQ12 DQ4 DQ13 DQ5 DQ14 DQ6 DQ15 ...
Page 4
... KMM366S1623CT ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin relative to Vss Voltage on V supply relative to Vss DD Storage temperature Power dissipation Short circuit current Note : Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. ...
Page 5
... KMM366S1623CT DC CHARACTERISTICS (Recommended operating condition unless otherwise noted, T Parameter Symbol Operating current I CC1 (one Bank Active) I CC2 Precharge standby current in power-down mode I CC2 I CC2 Precharge standby current in non power-down mode I CC2 I CC3 Active standby current in power-down mode I CC3 I CC3 Active standby current in ...
Page 6
... KMM366S1623CT AC OPERATING TEST CONDITIONS Parameter AC input levels (Vih/Vil) Input timing measurement reference level Input rise and fall time Output timing measurement reference level Output load condition 3.3V Output 870 (Fig output load circuit OPERATING AC PARAMETER (AC operating conditions unless otherwise noted) Parameter ...
Page 7
... KMM366S1623CT AC CHARACTERISTICS (AC operating conditions unless otherwise noted) REFER TO THE INDIVIDUAL COMPONENET, NOT THE WHOLE MODULE. Parameter CAS latency=3 CLK cycle time CAS latency=2 CAS latency=3 CLK to valid output delay CAS latency=2 CAS latency=3 Output data hold time CAS latency=2 CLK high pulse width ...
Page 8
... KMM366S1623CT- GH CAS Frequency Latency 100MHz (10.0ns) 2 83MHz (12.0ns) 2 75MHz (13.0ns) 2 66MHz (15.0ns) 2 60MHz (16.7ns) 2 KMM366S1623CT- GL CAS Frequency Latency 100MHz (10.0ns) 3 83MHz (12.0ns) 2 75MHz (13.0ns) 2 66MHz (15.0ns) 2 60MHz (16.7ns RAS RP 68ns 48ns ...
Page 9
... KMM366S1623CT SIMPLIFIED TRUTH TABLE Command Register Mode register set Auto refresh Entry Refresh Self refresh Exit Bank active & row addr. Auto precharge disable Read & column address Auto precharge enable Auto precharge disable Write & column address Auto precharge enable ...
Page 10
... KMM366S1623CT PACKAGE DIMENSIONS 0.118 (3.000) 0.125 0.375 (3.175) (9.525) 0.096 (2.44) A .118DIA 0.004 (3.000DIA 0.100) 0.350 (8.890) .450 (11.430) 0.250 (6.350) 0.123 (3.125 0.079 0.004 (2.000 0.100) Detail A Tolerances : 0.005(.13) unless otherwise specified The used device is 8Mx8 SDRAM, TSOP SDRAM Part No. : KM48S8030BT 5 ...