X24645F ICMIC [IC MICROSYSTEMS], X24645F Datasheet
X24645F
Related parts for X24645F
X24645F Summary of contents
Page 1
This X24645 device has been acquired by IC MICROSYSTEMS from Xicor, Inc. 64K Advanced 2-Wire Serial E FEATURES • 2.7V to 5.5V Power Supply • Low Power CMOS —Active Read Current Less Than 1mA —Active Write Current Less Than 3mA ...
Page 2
X24645 2 ICmic E PROMs are designed and tested for applications requiring extended endurance. Inherent data retention is greater than 100 years. PIN DESCRIPTIONS Serial Clock (SCL) The SCL input is used to clock all data into and out of ...
Page 3
X24645 DEVICE OPERATION The X24645 supports a bidirectional bus oriented pro- tocol. The protocol defines any device that sends data onto the bus as a transmitter, and the receiving device as the receiver. The device controlling the transfer is a ...
Page 4
X24645 Stop Condition All communications must be terminated by a stop condition, which is a LOW to HIGH transition of SDA when SCL is HIGH. The stop condition is also used to place the device into the standby power mode ...
Page 5
X24645 DEVICE ADDRESSING Following a start condition the master must output the address of the slave it is accessing (see Figure 4). The next two bits are the device select bits. A system could have up to four X24645’s on ...
Page 6
X24645 Page Write The X24645 is capable of a 32-byte page write operation initiated in the same manner as the byte write operation, but instead of terminating the write cycle after the first data word is transferred, the ...
Page 7
X24645 READ OPERATIONS Read operations are initiated in the same manner as write operations with the exception that the R/W bit of the slave address is set HIGH. There are three basic read operations: current address read, random read and ...
Page 8
X24645 Sequential Read Sequential reads can be initiated as either a current address read or random access read. The first byte is transmitted as with the other modes, however, the master now responds with an acknowledge, indicating it requires additional ...
Page 9
X24645 WRITE PROTECT REGISTER The Write Protect Register (WPR) is located at the highest address, 1FFFh. Figure 11. Write Protect Register WPR (ADDR = 1FFFh WPEN 0 0 BP1 BP0 WPR.1 = WEL –- “Write ...
Page 10
X24645 Block Protect Bits The Block Protect Bits BP0 and BP1 determine which blocks of the memory are write-protected: Table 1. Block Protect Bits Protected BP1 BP0 Addresses 0 0 None 0 1 1800h–1FFFh 1 0 1000h–1FFFh 1 1 0000h–1FFFh ...
Page 11
X24645 ABSOLUTE MAXIMUM RATINGS* Temperature under Bias X24645 ....................................... –65°C to +135°C Storage Temperature ........................ –65°C to +150°C Voltage on any Pin with Respect to V .................................... –1V to +7V SS D.C. Output Current .............................................. 5mA Lead Temperature (Soldering, .............................. ...
Page 12
X24645 A.C. CONDITIONS OF TEST V Input Pulse Levels CC Input Rise and Fall Times Input and Output Timing Levels A.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions, unless otherwise specified.) Read & Write Cycle Limits Symbol f SCL Clock ...
Page 13
X24645 Bus Timing SCL t SU:STA SDA IN SDA OUT Write Cycle Limits Symbol Parameter (6) T Write Cycle Time WR The write cycle time is the time from a valid stop condition of a write sequence to the end ...
Page 14
X24645 PACKAGING INFORMATION HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL 0.015 (0.38) TYP. 0.010 (0.25) NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH 8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P 0.430 ...
Page 15
X24645 PACKAGING INFORMATION 8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX 0.010 (0.25) 0.020 (0.50) 0° – 8° 0.016 (0.410) 0.037 (0.937) NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 0.150 (3.80) 0.158 (4.00) PIN ...
Page 16
X24645 PACKAGING INFORMATION 14-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX PIN 1 0.014 (0.35) 0.020 (0.51) (4X) 7° 0.050 (1.27) 0.010 (0.25) 0.020 (0.50) 0° – 8° 0.016 (0.41) 0.037 (0.937) NOTE: ALL DIMENSIONS IN ...
Page 17
X24645 PACKAGING INFORMATION 20-LEAD PLASTIC, TSSOP PACKAGE TYPE V 0° – 8° See Detail “A” NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) .025 (.65) BSC .169 .252 (6.4) BSC (4.3) .177 (4.5) .252 (6.4) .300 (6.6) .047 (1.20) ...
Page 18
X24645 ORDERING INFORMATION X24645 Device Part Mark Convention X24645 LIMITED WARRANTY Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied, ...