MASW-009276-000DIE MA-COM [M/A-COM Technology Solutions, Inc.], MASW-009276-000DIE Datasheet - Page 2

• Manufacturer Part Number: MASW-009276-000DIE
• Description: Bumped GaAs SP3T Switch for WLAN 1.0 - 4.0 GHz
• Manufacturer: MA-COM [M/A-COM Technology Solutions, Inc.]

2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.
Commitment to produce in volume is not guaranteed.
Bumped GaAs SP3T Switch for WLAN
1.0 - 4.0 GHz
Parts List
MASW-009276-000DIE
3. External blocking capacitors on all RF ports.
Recommended PCB Configuration
Electrical Specifications
Control Current
Insertion Loss
Return Loss
Parameter
Input P1dB
C1 - C4
C5 - C7
Harmonics
Isolation
Part
IP3
RFC to Tx/Rx/BT, 2.4 GHz, 20 dBm Total Power, 1MHz Spacing
1000 pF
Value
39 pF
3
: T
A
Case Style
RFC to Tx 2.4 GHz, 20 dBm
= 25°C, Z
RFC to Tx/Rx/BT, 2.4 GHz
0402
0402
RFC to Rx, 2.4 GHz
RFC to BT, 2.4 GHz
RFC to Rx, 2.4 GHz
RFC to BT, 2.4 GHz
RFC to Tx, 2.4 GHz
RFC to Tx, 2.4 GHz
Test Conditions
2.4 - 2.5 GHz
|Vc| = 3 V
0
= 50 Ω, Vc = 0 V / 3 V, Pin = 0 dBm
M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
changes to the product(s) or information contained herein without notice.
Truth Table
4. For positive voltage control, external DC blocking capacitors
5. Differential voltage, V(state 1) - V(state 0), must be
6. 0 = 0 ± 0.3 V, 1 = +2.7 V to +5 V.
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD)
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
• North America Tel: [phone] / Fax: [phone]
• Europe Tel: [phone] / Fax: [phone]
• Asia/Pacific Tel: [phone] / Fax: [phone]
V
Visit www.macomtech.com for additional data sheets and product information.
are required on all RF ports.
+2.7 V minimum and must not exceed +5 V.
1
0
0
C
1
V
0
1
0
C
2
4,5,6
V
0
0
1
C
3
Units
dBm
dBm
dBm
dB
dB
dB
dB
dB
µA
RFC–BT
Off
Off
On
Min.
20
30
20
—
—
—
—
—
—
—
—
RFC-T
and
Off
On
Off
Typ.
-75
0.5
<1
24
32
24
15
55
32
28
32
X
can
RFC-R
Rev. V1
Max.
Off
Off
On
0.75
—
—
—
—
—
—
—
—
—
2
be
X