WT11i-A-AI3 Bluegiga Technologies, WT11i-A-AI3 Datasheet
WT11i-A-AI3
Specifications of WT11i-A-AI3
Available stocks
Related parts for WT11i-A-AI3
WT11i-A-AI3 Summary of contents
Page 1
... WT11i-A DATA SHEET Monday, 28 November 2011 Version 1.45 ...
Page 2
... Bluegiga’s products are not authorized for use as critical components in life support devices or systems. The WRAP is a registered trademark of Bluegiga Technologies The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies. All other trademarks listed herein are owned by their respective owners. Bluegiga Technologies Oy ...
Page 3
... First draft Certification infromation added Release FCC radiation exposure statement updated FCC and IC statements updated, physical dimensions added WT11i description updated WT11i-E removed IC statement in French added Table 1: reset description corrected Contact details updated Terminal descriptions corrected, recommended PCB land pattern added, ...
Page 4
... Serial Peripheral Interface (SPI) ................................................................................................................. 26 8 PCM Codec Interface ................................................................................................................................. 27 8.1 PCM Interface Master/Slave ............................................................................................................... 27 8.2 Long Frame Sync ................................................................................................................................ 28 8.3 Short Frame Sync ............................................................................................................................... 28 8.4 Multi-slot Operation ............................................................................................................................. 29 8.5 GCI Interface ....................................................................................................................................... 29 8.6 Slots and Sample Formats .................................................................................................................. 30 8.7 Additional Features ............................................................................................................................. 31 8.8 PCM_CLK and PCM_SYNC Generation ............................................................................................ 31 8.9 PCM Configuration .............................................................................................................................. 32 9 I/O Parallel Ports ........................................................................................................................................ 34 9.1 PIO Defaults ........................................................................................................................................ 34 10 Reset ....................................................................................................................................................... 35 Bluegiga Technologies Oy ...
Page 5
... Pin States on Reset ..................................................................................................................... 35 11 Certifications ........................................................................................................................................... 36 11.1 Bluetooth ...................................................................................................................................... 36 11.2 FCC and IC .................................................................................................................................. 36 11.2.1 FCC et IC ..................................................................................................................................... 38 11.3 CE ................................................................................................................................................ 40 12 Contact Information................................................................................................................................. 41 Bluegiga Technologies Oy ...
Page 6
... DESCRIPTION WT11i is a fully integrated Bluetooth 2.1 + EDR, class 1 module combining antenna, Bluetooth radio and an on-board Bluetooth stack. The WT11i module utilizes Bluegiga's latest generation RF technology and provides better performance than its predecessor WT11. For OEM's WT11i offers trouble free Bluetooth integration for applications where the best performance is needed and it’ ...
Page 7
... Ordering Information WT11i-A-HCI Fimrware HCI21= HCI firmware (Bluetooth 2.1 + EDR) AI3 = iWRAP 3.0.0 AI4 = iWRAP 4.0 Custom* HW version A = Chip antenna, extended temperature range Product series Bluegiga Technologies Oy Page ...
Page 8
... USB- 9 UART_CTS# 10 PCM_IN 11 PCM_CLK 12 PCM_SYNC 13 GND 14 Figure 1: WT11i connection diagram PAD TYPE DESCRIPTION Input, internal 220kohm Active high reset. Keep high for >5 ms pull-down, internal start to cause a reset up reset circuitry GND GND Supply voltage Supply voltage for the RF power amplifier Supply voltage for BC4 and the flash ...
Page 9
... UART data input, active high state, with weak internal pull-down CMOS input, tri- UART clear to send, active low state, with weak internal pull-down Table 4: UART Terminal Descriptions Bluegiga Technologies Oy DESCRIPTION Programmamble input/output line Programmamble input/output line Programmamble input/output line Programmamble input/output ...
Page 10
... CMOS input with weak Chip select for Serial Peripheral internal pull-up Interface, active low CMOS input with weak SPI clock internal pull-down CMOS output, tristate, SPI data output with weak internal pull down Table 6: Terminal Descriptions Bluegiga Technologies Oy Page ...
Page 11
... Sleep - Inquiry - Min -40 -0.4 VSS-0.4 Table 7: Absolute Maximum Ratings Min -40 3.0 Table 8: Recommended Operating Conditions Power level 17 dBm dBm dBm Table 9: WT11i Current Consumption Bluegiga Technologies Oy Max Unit 85 °C 3.6 V VDD+0.4 V Max Unit 85 °C 3.6 V MAX AVG Unit 170 72 170 54 170 ...
Page 12
... PIO Current Sink and Source Capability 3.5 Antenna Specification WT11i uses a monopole type on a chip antenna with maximum gain of 0.5 dBi. The radiation pattern and the total radiated efficiency are dependent on the layout and any metal around the antenna has an effect on the radiation characteristics. Typically the efficiency is 30 … 50%. ...
Page 13
... Figure 4: Antenna radiation pattern in a USB dongle layout Figure 5: Antenna radiation pattern in a USB dongle layout Bluegiga Technologies Oy Page ...
Page 14
... Figure 6: Antenna radiation pattern in the WT11 evaluation kit Figure 7: Antenna radiation pattern in the WT11 evaluation kit Figure 8: Antenna radiation pattern in the WT11 eevaluation kit Bluegiga Technologies Oy Page ...
Page 15
... Physical Dimensions Figure 9: Physical dimensions (top view) 11.4mm 2.1mm 6.3mm Figure 10: Dimensions of WT11i Bluegiga Technologies Oy 35.8mm 2.6mm Page ...
Page 16
... Layout Guidelines WT11i is pin compatible with WT11 despite of slightly different external dimensions. For new design it recommended to follow the land pattern shown in the figure below. Figure 11: Recommended PCB land pattern for WT11i Do not place any copper under the antenna. The minimum recommended keep out area is shown in the figure 12 ...
Page 17
... Figure 12: Recommended metal keep put area for WT11i Effect of PCB thickness to the antenna impedance matching 0 -5 -10 -15 -20 -25 -30 -35 -40 2300 2350 Figure 13: Effect of FR4 under the antenna to the resonant frequency Use good layout practices to avoid excessive noise coupling to supply voltage traces or sensitive analog signal traces, such as analog audio signals ...
Page 18
... Recommended PCB layer configuration Overlapping GND layers without GND stitching vias Figure 15: Use of stitching vias to avoid emissions from the edges of the PCB Figure 14: Typical 4-layer PCB construction Bluegiga Technologies Oy Signals GND Power Signals Overlapping GND layers with GND stitching vias shielding the ...
Page 19
... UART_RX terminal, as shown in Figure 9. If tBRK is longer than the value, defined by PSKEY_HOST_IO_UART_RESET_TIMEOUT, (0x1a4), a reset will occur. This feature allows a host to initialise the system to a known state. Also, WT11i can emit a break character that may be used to wake the host. ...
Page 20
... Equation 1: Data Rate Table 11: Standard Data Rates Bluegiga Technologies Oy Page ...
Page 21
... UART Bypass 5.2 UART Configuration While Reset is Active The UART interface for WT11i while the chip is being held in reset is tristate. This will allow the user to daisy chain devices onto the physical UART bus. The constraint on this method is that any devices connected to this bus must tristate when WT11i reset is de-asserted and the firmware begins to run. ...
Page 22
... USB hub or root port. However, it requires that VBUS be connected to WT11i via a resistor network (Rvb1 and Rvb2), so WT11i can detect when VBUS is powered up. BlueCore4-External will not pull USB_DP high when VBUS is off ...
Page 23
... For WT11i, the USB power descriptor should be altered to reflect the amount of power required. This is accomplished by setting PSKEY_USB_MAX_POWER (0x2c6). This is higher than for a Class 2 application due to the extra current drawn by the Transmit RF PA. By default for WT11i the setting is 300 mA. When selecting a regulator, be aware that VBUS may go as low as 4.4V. The inrush current (when charging reservoir and supply decoupling capacitors) is limited by the USB specification ...
Page 24
... USB_WAKE_UP. These are outside the USB specification (no wires exist for them inside the USB cable), but can be useful when embedding WT11i into a circuit where no external USB is visible to the user. Both control lines are shared with PIO pins and can be assigned to any PIO pin by setting PSKEY_USB_PIO_DETACH and PSKEY_USB_PIO_WAKEUP to the selected PIO number ...
Page 25
... Bluetooth software running on the host computer. Please, contact 6.9 USB v2.0 Compliance and Compatibility Although WT11i meets the USB specification, CSR cannot guarantee that an application circuit designed around the module is USB compliant. The choice of application circuit, component choice and PCB layout all affect USB signal quality and electrical characteristics. The information in this document is intended as a guide and should be read in association with the USB specification, with particular attention being given to Chapter 7 ...
Page 26
... The SPI port can be used for system debugging. It can also be used for programming the Flash memory and setting the PSKEY configurations. WT11i uses 16-bit data and 16-bit address serial peripheral interface, where transactions may occur when the internal processor is running or is stopped. SPI interface is connected using the MOSI, MISO, CSB and CLK pins ...
Page 27
... It does not pass through the HCI protocol layer. Hardware on WT11i allows the data to be sent to and received from a SCO connection three SCO connections can be supported by the PCM interface at any one time. ...
Page 28
... PCM_CLK to half the PCM_SYNC rate, i.e., 62.5s long. Figure 24: Long Frame Sync (Shown with 8-bit Companded Sample) WT11i samples PCM_IN on the falling edge of PCM_CLK and transmits PCM_OUT on the rising edge. PCM_OUT may be configured to be high impedance on the falling edge of PCM_CLK in the LSB position or on the rising edge ...
Page 29
... Figure 26: Multi-slot Operation with Two Slots and 8-bit Companded Samples 8.5 GCI Interface WT11i is compatible with the GCI, a standard synchronous 2B+D ISDN timing interface. The two 64kbits/s B channels can be accessed when this mode is configured. Bluegiga Technologies Oy ...
Page 30
... The start of frame is indicated by the rising edge of PCM_SYNC and runs at 8kHz. With WT11i in Slave mode, the frequency of PCM_CLK can 4.096MHz. 8.6 Slots and Sample Formats WT11i can receive and transmit on any selection of the first four slots following each sync pulse. Slot durations can be either clock cycles ...
Page 31
... Figure 28: 16-bit Slot Length and Sample Formats 8.7 Additional Features WT11i has a mute facility that forces PCM_OUT master mode, PCM_SYNC may also be forced to 0 while keeping PCM_CLK running which some codecs use to control power down. 8.8 PCM_CLK and PCM_SYNC Generation WT11i has two methods of generating PCM_CLK and PCM_SYNC in master mode. The first is generating these signals by DDS from BlueCore4-External internal 4MHz clock ...
Page 32
... PSKEY_PCM_LOW_JITTER_CONFIG in Table 13. The default for PSKEY_PCM_CONFIG32 is 0x00800000, i.e., first slot following sync is active, 13-bit linear voice format, long frame sync and interface master generating 256kHz PCM_CLK from 4MHz internal clock with no tri-state of PCM_OUT. PCM_CLK at 512kHz Bluegiga Technologies Oy with PCM_SYNC at Page 8kHz, ...
Page 33
... Default is 0001. Ignored by firmaware Selects between 13 (0b00), 16 (0b01), 8 (0b10) bit sample with 16 cycle slot duration 8 (0b11) bit sample 8 cycle slot duration. Description Sets PCM_CLK counter limit Sets PCM_CLK count rate. Sets PCM_SYNC division relative to PCM_CLK. Bluegiga Technologies Oy Page ...
Page 34
... Any of the PIO lines can be configured as interrupt request lines or as wake-up lines from sleep modes. WT11i has a general purpose analogue interface pin AIO[1]. This is used to access internal circuitry and control signals. It may be configured to provide additional functionality. ...
Page 35
... Reset WT11i may be reset from several sources: RESET pin, power on reset, a UART break character or via software configured watchdog timer. The RESET pin is an active low reset and is internally filtered using the internal low frequency clock oscillator. A reset will be performed between 1.5 and 4.0ms following RESETB being active ...
Page 36
... Certifications WT11i-A is compliant to the following specifications. 11.1 Bluetooth WT11i-A module is Bluetooth qualified and listed as a controller subsystem and it is Bluetooth compliant to the following profiles of the core spec version 2.1/2.1+EDR. Baseband HCI Link Manager Radio 11.2 FCC and IC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ...
Page 37
... FCC and Industry Canada authorization. End Product Labeling The WT11i-A Module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module ...
Page 38
... Les responsabilités de l’intégrateur afin de satisfaire aux réglementations de la FCC et d’Industrie Canada : Les modules WT11i ont été certifiés pour entrer dans la fabrication de produits exclusivement réalisés par des intégrateurs dans les conditions suivantes : Bluegiga Technologies Oy ...
Page 39
... Contient un module transmetteur certifié FCC QOQWT11I » « Contient un module transmetteur certifié IC 5123A-BGTWT11I » ou « Inclut la certification FCC QOQWT11I » « Inclut la certification IC 5123A-BGTWT11I » L’intégrateur du module WT11i ne doit utiliser que les antennes répertoriées dans le tableau 21 certifiées pour ce module. Bluegiga Technologies Oy Page ...
Page 40
... En outre, cette antenne ne devra en aucun cas être installée ou utilisée en concomitance avec une autre antenne ou un autre transmetteur. 11.3 CE WT11i meets the requirements of the standards below and hence fulfills the requirements of EMC Directive 89/336/EEC as amended by Directives 92/31/EEC and 93/68/EEC within CE marking requirement. ...
Page 41
... Satellite Boulevard, Building 400, Suite 300 Duluth, GA, 30096, USA Sales Office / Hong-Kong: Phone: Fax: +852 3972 5777 Bluegiga Technologies, Inc. 19/F Silver Fortune Plaza, 1 Wellington Street, Central Hong Kong +1 770 291 2181 +1 770 291 2183 +852 3182 7321 Bluegiga Technologies Oy Page ...