MAXQ8913X-0000+ Maxim Integrated, MAXQ8913X-0000+ Datasheet - Page 9

• Manufacturer Part Number: MAXQ8913X-0000+
• Description: 16-bit Microcontrollers - MCU 16-Bit Mxd Sgnl MCU w/Op Amp ADC & DAC
• Manufacturer: Maxim Integrated

Specifications of MAXQ8913X-0000+

• Rohs: yes
• Core: RISC
• Processor Series: MAXQ8913
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 20 MHz
• Program Memory Size: 64 KB
• Data Ram Size: 4 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2.7 V to 3.6 V
• Package / Case: WLP-58
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 7
• Interface Type: I2C, SPI, USART
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Program Memory Type: Flash
• Part # Aliases: 90-08913+D02

I
(V
Figure 4. Series Resistors (R
Note 15: Devices that use nonstandard supply voltages that do not conform to the intended I
Note 16: Maximum V
Note 17: C
Note 18: The maximum fall time of 300ns for the SDA and SCL bus lines as shown in the I
Note 19: I/O pins of fast-mode devices must not obstruct the SDA and SCL lines if V
2
Input Low Voltage
Input High Voltage
Input Hysteresis (Schmitt)
Output Logic-Low (Open Drain
or Open Collector)
Output Fall Time from V
to V
Capacitance from 10pF to
400pF (Notes 17, 18)
Pulse Width of Spike Filtering
That Must Be Suppressed by
Input Filter
Input Current Each I/O Pin
with an Input Voltage
Between 0.1 x V
x V
I/O Capacitance
16-Bit, Mixed-Signal Microcontroller with Op Amps,
DVDD
C BUS CONTROLLER AC CHARACTERISTICS
DVDD(MAX)
IL(MAX)
ADC, and DACs for All-in-One Servo Loop Control
= 1.8V to 3.6V, T
PARAMETER
input levels to the V
than the specified maximum t
nected between the SDA/SCL pins and the SDA/SCL bus lines as shown in the I
Slave) table without exceeding the maximum specified fall time. See Figure 4.
B
with Bus
= capacitance of one bus line in pF.
(Note 19)
DVDD
_______________________________________________________________________________________
IH_I2C
and 0.9
A
IH(MIN)
= -40°C to +85°C.) (See Figure 4.)
S
= V
) for Protecting Against High-Voltage Spikes
DVDD
DVDD(MAX)
SYMBOL
V
V
C
V
t
t
V
IHYS_I2C
I
voltage to which the pullup resistors R
OF_I2C
SP_I2C
OL_I2C
IN_I2C
IH_I2C
IO_I2C
IL_I2C
OF_I2C
SDA
SCL
+ 0.5V.
V
of 250ns for the output stages. This allows series protection resistors (R
DVDD
CONDITIONS
sink current
V
DEVICE
V
DVDD
DVDD
I
R
2
TEST
S
C
> 2V, 3mA
> 2V
R
S
DEVICE
V
0.7 x V
DVDD
I
R
2
C
S
STANDARD MODE
MIN
-0.5
-10
0
R
DVDD
P
S
are connected.
0.3 x V
R
P
MAX
+10
DVDD
250
0.4
10
DVDD
R
P
2
2
is switched off.
C Bus Controller Timing (Acting as I
C Bus Controller Timing table is longer
2
C-bus system levels must relate their
0.7 x V
20 + 0.1C
V
0.05 x
MIN
-0.5
DVDD
-10
0
0
FAST MODE
DVDD
B
0.3 x V
(Note 15)
(Note 16)
MAX
+10
250
0.4
50
10
DVDD
s
) to be con-
UNITS
μA
ns
ns
pF
2
V
V
V
V
C
9