MAX5873EVKIT Maxim Integrated, MAX5873EVKIT Datasheet - Page 2

• Manufacturer Part Number: MAX5873EVKIT
• Description: Digital to Analog Converters - DAC Evaluation Kit for the MAX5873 MAX5874 MAX5875
• Manufacturer: Maxim Integrated

Specifications of MAX5873EVKIT

• Number Of Converters: 2
• Conversion Rate: 200 MSPs
• Resolution: 12 bit
• Interface Type: Parallel
• Supply Voltage - Max: 1.89 V, 3.465 V
• Supply Voltage - Min: 1.71 V, 3.135 V

•
•
•
•
•
•
The EV kit is a fully assembled and tested surface-mount
board. Follow the steps below for board operation. Do
not turn on power supplies or enable signal genera-
tors until all connections are completed (Figure 1).
1) Verify that a shunt is installed across pins 1 and 2 of
2) Verify that shunts are installed across pins 2 and 3
MAX5873/MAX5874/MAX5875 Evaluation Kits
2
MAX5873EVKIT
MAX5874EVKIT
MAX5875EVKIT
DESIGNATION
EV KIT PART
Three 3.3V, 100mA DC power supplies
Two 1.8V, 100mA DC power supplies
Two signal generators with low phase noise and low
jitter for clock inputs (e.g., Agilent 8644B)
A dual, 12-bit (MAX5873), 14-bit (MAX5874), or 16-
bit (MAX5875) digital pattern generator for data
inputs (e.g., DG2020A)
Spectrum analyzer (e.g., Rohde & Schwartz FSU)
Voltmeter
jumper JU1 (dual-port input enabled).
of jumpers JU2 (normal operation), and JU3 (offset
binary input mode).
_______________________________________________________________________________________
NUMBER
T1, T2, T3
R10–R47
EV Kit Specific Component List
T4, T5
U1
DESIGNATION
QTY
0
3
2
1
Recommended Equipment
U1
Not installed, resistors (0603)
1:1 RF transformers
Mini-Circuits ADTL1-12
1:1 RF transformers
Coilcraft TTWB3010-1
See the EV Kit Specific
Component List
10mm x 10mm x 0.9mm)
10mm x 10mm x 0.9mm)
10mm x 10mm x 0.9mm)
DESCRIPTION
Quick Start
(68-pin QFN-EP,
(68-pin QFN-EP,
(68-pin QFN-EP,
DESCRIPTION
MAX5873EGK
MAX5874EGK
MAX5875EGK
Common Component List (continued)
3) Verify that no shunts are installed across jumpers
4) Install a shunt across pin J1-37 (header J1) and
5) Install a shunt across pin J1-33 (header J1) and
6) Synchronize the digital pattern generator (DG2020A)
7) Connect the clock signal generator to the CLK SMA
8) Verify that the digital pattern generator is pro-
9) Connect the digital pattern generator outputs to the
10) Connect the spectrum analyzer to the OUTPUTQ
Note: Indicate that you are using the MAX5873/MAX5874/
MAX5875 when contacting these manufacturers.
AVX
Coilcraft
Fair-Rite Products
IRC
Kemet
Mini-Circuits
Taiyo Yuden
TDK
DESIGNATION
JU4 and JU5 (internal reference).
ground (pin J1-38) (XOR disabled).
DGND (pin J1-34) to ground the SELIQ pin (recom-
mended for dual-port input operation).
and the spectrum analyzer to the clock signal
generator.
connector on the EV kit.
grammed for valid CMOS output voltage levels and
offset binary digital outputs.
J1 and J2 input header connectors on the EV kit
board. See the Pattern Generator Connection sec-
tion for proper connection.
SMA connector or to the OUTPUTI SMA connector.
SUPPLIER
U2
—
—
843-946-0238
847-639-6400
845-895-2055
361-992-7900
864-963-6300
718-934-4500
800-348-2496
847-803-6100
QTY
1
5
1
PHONE
Component Suppliers
1.25V voltage reference
(8-pin SO)
MAX6161AESA or
MAX6161BESA
Shunts (JU1–JU5)
MAX5875 PC board
www.avxcorp.com
www.coilcraft.com
www.fair-rite.com
www.irctt.com
www.kemet.com
www.minicircuits.com
www.t-yuden.com
www.component.tdk.com
DESCRIPTION
WEBSITE