AT24MAC402-SSHM-T Atmel, AT24MAC402-SSHM-T Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
AT24MAC402-SSHM-T
Manufacturer Part Number
AT24MAC402-SSHM-T
Description
EEPROM 2-Kbit Serial EEPROM
Manufacturer
Atmel
Datasheet
1.AT24MAC602-SSHM-T.pdf
(28 pages)
Specifications of AT24MAC402-SSHM-T
Rohs
yes
Memory Size
2 Kbit
Organization
256 B x 8
Data Retention
100 yr
Maximum Clock Frequency
1000 KHz
Maximum Operating Current
6 uA
Operating Supply Voltage
1.7 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
SOIC-8
5.
Figure 4-6. Output Acknowledge
Device Addressing
Standard EEPROM Access: The 2K EEPROM requires an 8-bit device address word following a start condition to
enable the chip for a read or write operation (see
The device address word consists of a mandatory one-zero sequence for the first four most-significant bits ‘1010’(Ah)
for normal read and write operations and ‘0110’ (6h) for writing to the Software Write Protect Register.
The next three bits in the protocol sequence are the A2, A1, and A0 device address bits. These three bits must match
their corresponding hard-wired input pins A
The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high,
and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero.
If a compare is not made, the device will return to a standby state. The device will not acknowledge if the Write Protect
Register has been programmed and the control code is ‘0110’(6h).
Serial Number Access: The AT24MAC402/602 incorporates an extended memory block containing a
factory-programmed 128-bit serial number. Access to this memory location is obtained by beginning the device address
word with a ‘1011’(Bh) sequence. The behavior of the next three bits (A2, A1, and A0) remain the same as during a
standard memory addressing sequence.
The eighth bit of the device address needs to be set to a one to read the serial number. A zero in this bit position, other
than during a dummy write sequence to set the address pointer, will result in a unknown condition and behavior. Writing
or altering the 128-bit serial number is not possible as it is permanently write protected. Further specific protocol is
needed to address the serial number feature of the part. For more details on accessing this special feature, See
Operations” on page
EUI Address Access: The AT24MAC402/602 utilizes an extended memory block containing a factory-programmed
read-only EUI-48 or EUI-64 address respectively. Access to this memory block is obtained by beginning the device
address word with a ‘1011’ (Bh) sequence. The behavior of the next three bits (A2, A1, and A0) remain the same as
during a standard memory addressing sequence.
The eighth bit of the device address needs to be set to a one to read the EUI address. A zero in this bit position, other
than during a dummy write sequence to set the address pointer, will result in a unknown condition and behavior.
Attempting to write or alter the EUI address is not possible as it is permanently write protected. Further specific protocol
is needed to address this feature of the part. For more details on accessing this special feature, see
on page
Data OUT
Data IN
SCL
15.
Start
15.
1
2
, A
1
, and A
Table 8-1 on page
Atmel AT24MAC402/602 [PRELIMINARY DATASHEET]
8
0
in order for the part to acknowledge.
Acknowledge
9
16).
8807B–SEEPR–9/2012
“Read Operations”
“Read
10