AT24C08C-PUM Atmel, AT24C08C-PUM Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
AT24C08C-PUM
Manufacturer Part Number
AT24C08C-PUM
Description
EEPROM 8K (1024x8) 2-WIRE 1.7V
Manufacturer
Atmel
Datasheet
1.AT24C08C-SSHM-T.pdf
(24 pages)
Specifications of AT24C08C-PUM
Rohs
yes
Factory Pack Quantity
50
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT24C08C-PUM
Manufacturer:
ATMEL
Quantity:
5 000
Part Number:
AT24C08C-PUM
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
6.
7.
Device Addressing
Standard EEPROM Access: The 4K and 8K EEPROM device requires an 8-bit device address word following a start
condition to enable the chip for a read or write operation. The device address word consists of a mandatory “1010” (0xA)
sequence for the first four Most Significant Bits (MSB) as shown in
EEPROM devices.
The 4K EEPROM only uses the A2 and A1 device address bits with the third bit being a memory page address bit. The
two device address bits must compare to their corresponding hard-wired input pins. The A
The 8K EEPROM only uses the A2 device address bit with the next two bits being for memory page addressing. The A2
address bit must compare to its corresponding hard-wired input pin. The A
The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high and
a write operation is initiated if this bit is low.
Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the chip will return to
a standby state.
For the SOT23 package offering, the 4K EEPROM software A2 and A1 bits in the device address word must be set to
zero to properly communicate. The 8K EEPROM software A2 bit in the device address word must be set to zero to
properly communicate.
Write Operations
Byte Write: A write operation requires an 8-bit data word address following the device address word and
acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first
8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero and the addressing device, such
as a microcontroller, must terminate the write sequence with a Stop condition. At this time the EEPROM enters an
internally timed write cycle, t
EEPROM will not respond until the write is complete (see
Page Write: The 4K and 8K EEPROM devices are capable of a 16-byte Page Write.
A Page Write is initiated in the same way as a Byte Write, but the microcontroller does not send a Stop condition after the
first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller
can transmit up to fifteen more data words. The EEPROM will respond with a zero after each data word received. The
microcontroller must terminate the Page Write sequence with a Stop condition (see
The data word address lower four bits are internally incremented following the receipt of each data word. The higher data
word address bits are not incremented, retaining the memory page row location. When the word address, internally
generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than eight
data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten.
Acknowledge Polling: Once the internally timed write cycle has started and the EEPROM inputs are disabled,
Acknowledge Polling can be initiated. This involves sending a Start condition followed by the device address word. The
read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM
respond with a zero allowing the read or write sequence to continue.
WR
, to the nonvolatile memory. All inputs are disabled during this write cycle and the
Figure 8-2 on page
Figure 8-1 on page
Atmel AT24C04C/08C [DATASHEET]
1
and A
11).
0
pins are no connect.
Figure 8-3 on page
11. This is common to all the
0
pin is no connect.
8787C–SEEPR–7/12
12).
10