LCMXO2-4000ZE-1FG484C Lattice, LCMXO2-4000ZE-1FG484C Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/3/380/lattice_sml.jpg)
LCMXO2-4000ZE-1FG484C
Manufacturer Part Number
LCMXO2-4000ZE-1FG484C
Description
FPGA - Field Programmable Gate Array 4320 LUTs 279 IO 1.2V 1 Spd
Manufacturer
Lattice
Datasheet
1.LCMXO2-256HC-4SG32I.pdf
(106 pages)
Specifications of LCMXO2-4000ZE-1FG484C
Rohs
yes
Number Of Gates
4 K
Embedded Block Ram - Ebr
92 Kbit
Number Of I/os
279
Maximum Operating Frequency
104 MHz
Operating Supply Voltage
1.14 V to 1.26 V, 1.14 V to 3.465 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
fpBGA-484
Distributed Ram
34 Kbit
Minimum Operating Temperature
0 C
Operating Supply Current
124 uA
Factory Pack Quantity
60
User Flash Memory - Ufm
96 Kbit
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LCMXO2-4000ZE-1FG484C
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
For further information on the sysMEM EBR block, please refer to TN1201,
Devices.
EBR Asynchronous Reset
EBR asynchronous reset or GSR (if used) can only be applied if all clock enables are low for a clock cycle before
the reset is applied and released a clock cycle after the reset is released, as shown in Figure 2-10. The GSR input
to the EBR is always asynchronous.
Figure 2-10. EBR Asynchronous Reset (Including GSR) Timing Diagram
If all clock enables remain enabled, the EBR asynchronous reset or GSR may only be applied and released after
the EBR read and write clock inputs are in a steady state condition for a minimum of 1/f
release must adhere to the EBR synchronous reset setup time before the next active read or write clock edge.
If an EBR is pre-loaded during configuration, the GSR input must be disabled or the release of the GSR during
device wake up must occur before the release of the device I/Os becoming active.
These instructions apply to all EBR RAM, ROM and FIFO implementations. For the EBR FIFO mode, the GSR sig-
nal is always enabled and the WE and RE signals act like the clock enable signals in Figure 2-10. The reset timing
rules apply to the RPReset input versus the RE input and the RST input versus the WE and RE inputs. Both RST
and RPReset are always asynchronous EBR inputs. For more details refer to TN1201,
MachXO2
Note that there are no reset restrictions if the EBR synchronous reset is used and the EBR GSR input is disabled.
Programmable I/O Cells (PIC)
The programmable logic associated with an I/O is called a PIO. The individual PIO are connected to their respec-
tive sysIO buffers and pads. On the MachXO2 devices, the PIO cells are assembled into groups of four PIO cells
called a Programmable I/O Cell or PIC. The PICs are placed on all four sides of the device.
On all the MachXO2 devices, two adjacent PIOs can be combined to provide a complementary output driver pair.
The MachXO2-640U, MachXO2-1200/U and higher density devices contain enhanced I/O capability. All PIO pairs
on these larger devices can implement differential receivers. Half of the PIO pairs on the top edge of these devices
can be configured as true LVDS transmit pairs. The PIO pairs on the bottom edge of these higher density devices
have on-chip differential termination and also provide PCI support.
Devices.
Reset
Clock
Clock
Enable
2-13
Memory Usage Guide for MachXO2
MachXO2 Family Data Sheet
MAX
Memory Usage Guide for
(EBR clock). The reset
Architecture