KSZ8041FTL-S Micrel, KSZ8041FTL-S Datasheet - Page 14

• Manufacturer Part Number: KSZ8041FTL-S
• Description: Ethernet ICs 10/100 PHY Fibre version and SMII
• Manufacturer: Micrel
• Type: Single Port 10/100 Mb/s Ethernet Physical Layer Transceiverr

Specifications of KSZ8041FTL-S

• Rohs: yes
• Product: Ethernet Transceivers
• Number Of Transceivers: 1
• Data Rate: 10 Mb/s, 100 Mb/s
• Supply Voltage - Max: 3.465 V
• Supply Voltage - Min: 3.135 V
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-48
• Ethernet Connection Type: 10Base-T, 100Base-FX, 100Base-TX
• Maximum Supply Current: 58.3 mA
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT

Notes:
Micrel, Inc.
April 2007
1. P = Power supply.
2. MII Rx Mode: The RXD[3..0] bits are synchronous with RXCLK. When RXDV is asserted, RXD[3..0] presents valid data to MAC through the MII.
3. RMII Rx Mode: The RXD[1:0] bits are synchronous with REF_CLK. For each clock period in which CRS_DV is asserted, two bits of recovered
4. SMII Rx Mode: Receive data and control information are sent in 10 bit segments. In 100MBit mode, each segment represents a new byte of
5. MII Tx Mode: The TXD[3..0] bits are synchronous with TXCLK. When TXEN is asserted, TXD[3..0] presents valid data from the MAC through
6. RMII Tx Mode: The TXD[1:0] bits are synchronous with REF_CLK. For each clock period in which TX_EN is asserted, two bits of data are
7. SMII Tx Mode: Transmit data and control information are received in 10 bit segments. In 100MBit mode, each segment represents a new byte
(KSZ8041FTL)
(KSZ8041TL)
Pin Number
Gnd = Ground.
I = Input.
O = Output.
I/O = Bi-directional.
Ipd = Input with internal pull-down (40K +/-30%).
Ipu = Input with internal pull-up (40K +/-30%).
Opu = Output with internal pull-up (40K +/-30%).
Ipu/O = Input with internal pull-up (40K +/-30%) during power-up/reset; output pin otherwise.
Ipd/O = Input with internal pull-down (40K +/-30%) during power-up/reset; output pin otherwise.
RXD[3..0] is invalid when RXDV is de-asserted.
data are sent from the PHY.
data. In 10MBit mode, each segment is repeated ten times; therefore, every ten segments represent a new byte of data. The MAC can sample
any one of every 10 segments in 10MBit mode.
the MII. TXD[3..0] has no effect when TXEN is de-asserted.
received by the PHY from the MAC.
of data. In 10MBit mode, each segment is repeated ten times; therefore, every ten segments represent a new byte of data. The PHY can
sample any one of every 10 segments in 10MBit mode.
47
48
48
Pin Name
FXSD /
FXEN
RST#
NC
Type
Ipd
I
-
(1)
Pin Function
Chip Reset (active low)
No connect
FXSD:
FXEN:
If FXEN=0, fiber mode is disabled. PHY is in copper mode. The default is “0”.
See “100Base-FX Operation” section for details.
Signal Detect for 100Base-FX fiber mode
Fiber Enable for 100Base-FX fiber mode
14
KSZ8041TL/FTL
M9999-042707-1.1