MAX98090AETL+ Maxim Integrated, MAX98090AETL+ Datasheet - Page 157
MAX98090AETL+
Manufacturer Part Number
MAX98090AETL+
Description
Interface - CODECs 5V 130mW Stereo Headphone Amp
Manufacturer
Maxim Integrated
Datasheet
1.MAX98090BETL.pdf
(166 pages)
Specifications of MAX98090AETL+
Rohs
yes
- Current page: 157 of 166
- Download datasheet (13Mb)
MAX98090
The slave address with the R/W bit set to 0 indicates that
the master intends to write data to the MAX98090. The
MAX98090 acknowledges receipt of the address byte
during the master-generated 9th SCL pulse.
The second byte transmitted from the master configures
the MAX98090’s internal register address pointer. The
pointer tells the MAX98090 where to write the next byte
of data. An acknowledge pulse is sent by the MAX98090
upon receipt of the address pointer data.
The third byte sent to the MAX98090 contains the data
that is written to the chosen register. An acknowledge
pulse from the MAX98090 signals receipt of the data
byte. The address pointer autoincrements to the next
register address after each received data byte. This auto-
increment feature allows a master to write to sequential
registers within one continuous frame. The master signals
the end of transmission by issuing a STOP condition.
Register addresses greater than 0xE7 are reserved. Do
not write to these addresses.
Read Data Format
Send the slave address with the R/W bit set to 1 to initiate
a read operation. The MAX98090 acknowledges receipt
of its slave address by pulling SDA low during the 9th SCL
clock pulse. A START command followed by a read com-
mand resets the address pointer to register 0x00.
Figure 51. Reading One Byte of Data from the MAX98090
Figure 52. Reading n-Bytes of Data from the MAX98090
www.maximintegrated.com
S
ACKNOWLEDGE FROM MAX98090
S
ACKNOWLEDGE FROM MAX98090
SLAVE ADDRESS
SLAVE ADDRESS
R/W
R/W
O
O
A
ACKNOWLEDGE FROM MAX98090
A
ACKNOWLEDGE FROM MAX98090
REGISTER ADDRESS
REGISTER ADDRESS
REPEATED START
REPEATED START
A
A Sr
Sr
ACKNOWLEDGE FROM MAX98090
ACKNOWLEDGE FROM MAX98090
The first byte transmitted from the MAX98090 is the con-
tents of register 0x00. Transmitted data is valid on the
rising edge of SCL. The address pointer autoincrements
after each read data byte. This autoincrement feature
allows all registers to be read sequentially within one con-
tinuous frame. A STOP condition can be issued after any
number of read data bytes. If a STOP condition is issued
followed by another read operation, the first data byte to
be read will be from register 0x00.
The address pointer can be preset to a specific register
before a read command is issued. The master presets the
address pointer by first sending the MAX98090’s slave
address with the R/W bit set to 0 followed by the register
address. A REPEATED START condition is then sent fol-
lowed by the slave address with the R/W bit set to 1. The
MAX98090 then transmits the contents of the specified
register, and the address pointer autoincrements after
transmitting the first byte.
The master acknowledges receipt of each read byte
during the acknowledge clock pulse. The master must
acknowledge all correctly received bytes except the last
byte. The final byte must be followed by a not acknowl-
edge from the master and then a STOP condition.
Figure 51 illustrates the frame format for reading one byte
from the MAX98090. Figure 52 illustrates the frame for-
mat for reading multiple bytes from the MAX98090.
SLAVE ADDRESS
SLAVE ADDRESS
Ultra-Low Power Stereo Audio Codec
R/W
AUTOINCREMENT INTERNAL REGISTER ADDRESS POINTER
R/W
AUTOINCREMENT INTERNAL REGISTER ADDRESS POINTER
1
1
A
A
NOT ACKNOWLEDGE FROM MASTER
DATA BYTE
1 BYTE
DATA BYTE
1 BYTE
Maxim Integrated │ 157
A
P
A
Related parts for MAX98090AETL+
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: