FT200XD-R FTDI, FT200XD-R Datasheet
FT200XD-R
Specifications of FT200XD-R
Related parts for FT200XD-R
FT200XD-R Summary of contents
Page 1
... Future Technology Devices International Ltd FT200XD (USB I2C SLAVE IC) The FT200XD is a USB to I with the following advanced features: 2 Single chip USB interface. 3.4MHz, high speed mode, I Entire USB protocol handled on the chip. No USB specific firmware programming required. ...
Page 2
... Note: Packing codes for -x is Taped and Reel, 5,000pcs per reel - T: Tray packing, 490pcs per tray For example: FT200XD-R is 5,000pcs taped and reel packing Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 ...
Page 3
... USB Compliant The FT200XD is fully compliant with the USB 2.0 specification and has been given the USB-IF Test-ID (TID) 40001459 (Rev D). Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Version 1.3 3 ...
Page 4
... Multiplier Oscillator GND Figure 2.1FT200XD Block Diagram For a description of each function please refer to Section 4. Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 1V8 Internal Core Supply FIFO RX Buffer (512 bytes) USB ...
Page 5
... VCP and D2xx Interfaces ............................................................................................ 25 9.1.2 Reading and Writing Data ........................................................................................... Interface ..................................................................................... 27 9.2.1 Addressing ................................................................................................................ 27 9.2.2 Data Transfers .......................................................................................................... 27 2 9.3 Other I C Commands ........................................................................ 29 10 Internal MTP Memory Configuration ........................................... 31 Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Version 1.3 5 ...
Page 6
... DFN-10 Package Mechanical Dimensions ....................................... 36 11.2 Package Markings .......................................................................... 37 11.3 Solder Reflow Profile ..................................................................... 38 12 Contact Information ................................................................... 39 Appendix A – References ........................................................................... 40 Appendix B - List of Figures and Tables ..................................................... 41 Appendix C - Revision History .................................................................... 42 Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 2 C .................................................................... 32 Version 1.3 6 ...
Page 7
... Pin No. Name 1 USBDM 10 USBDP 2 RESET# Table 3.2 Common Function pins Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Type POWER 5 V (or 3V3) supply to IC Input POWER 1V8 - 3V3 supply for the IO cells Input 3V3 output at 50mA ...
Page 8
... These pins can be programmed to gently pull low during USB suspend (PWREN# = “1”) by setting an option in the MTP memory. 2. Clock stretching is not supported Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Type 2 ...
Page 9
... Keep_Awake# CBUS0 Table 3.4 CBUS Configuration Control *When in USB suspend mode the outputs clocks are also suspended. Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Description IO Pad is tri-stated Output a constant 1 Output a constant 0 Output is low after the device has been configured by USB, then high during USB suspend mode ...
Page 10
... The following paragraphs detail each function within the FT200XD. Please refer to the block diagram shown in Figure 2.1. Internal MTP Memory. The internal MTP memory in the FT200XD is used to store USB Vendor ID (VID), Product ID (PID), device serial number, product description string and various other USB configuration descriptors ...
Page 11
... High Speed Serial Mode. RESET Generator - The integrated Reset Generator Cell provides a reliable power-on reset to the device internal circuitry at power up. The RESET# input pin allows an external device to reset the FT200XD. RESET# can be tied to 3V3OUT. Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No ...
Page 12
... The FT200XD device only operates as a slave, and is capable of speeds up to 3.4MBit/s. There are four potential modes of operation for a given bus device, although most devices only use a single role (Master or Slave) and its two modes (Transmit and Receive): Master transmit – ...
Page 13
... Devices Characteristics and Ratings 6.1 Absolute Maximum Ratings The absolute maximum ratings for the FT200XD devices are as follows. These are in accordance with the Absolute Maximum Rating System (IEC 60134). Exceeding these may cause permanent damage to the device. Parameter Storage Temperature Floor Life (Out of Bag) At Factory Ambient (30° ...
Page 14
... VCC2 Supply Voltage Operating Supply Icc1 Current Operating Supply Icc2 Current 3V3 3.3v regulator output Table 6.3 Operating Voltage and Current Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Minimum Typical Maximum 2.97 5 5.5 1.62 --- 3.63 6 ...
Page 15
... Table 6.4 I/O Pin Characteristics VCCIO = +3.3V (except USB PHY pins) * The I/O drive strength and slow slew-rate are configurable in the MTP memory. Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Minimum Typical Maximum 2 ...
Page 16
... Table 6.5 I/O Pin Characteristics VCCIO = +2.5V (except USB PHY pins) * The I/O drive strength and slow slew-rate are configurable in the MTP memory. Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Minimum Typical Maximum 2 ...
Page 17
... Table 6.6 I/O Pin Characteristics VCCIO = +1.8V (except USB PHY pins) * The I/O drive strength and slow slew-rate are configurable in the MTP memory. Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Minimum Typical Maximum 1 ...
Page 18
... The internal Clock Oscillator has the following characteristics: Parameter Minimum Frequency of Operation (see Note 1) Clock Period Duty Cycle Table 6.9 Internal Clock Characteristics Note 1: Equivalent to +/-1667ppm Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Minimum Typical Maximum VCC-0 2.0 Unit ...
Page 19
... The power descriptors in the internal MTP Memory of the FT200XDmustbe programmed to match the current drawn by the device. A ferrite bead is connected in series with the USB power supply to reduce EMI noise from the FT200XD and associated circuitry being radiated down the USB cable to the USB host. The value of the Ferrite Bead depends on the total current drawn by the application ...
Page 20
... USBDP is pulled up to +3.3V, thus identifying the device as a full speed device to the USB host or hub. When the USB host or hub is powered off, VBUS_Sense pin will be low and the FT200XDis held in a suspend state. In this state the internal 1.5kΩ resistor is not pulled up to any power supply (hub or host is powered down current flows down USBDP via the 1.5kΩ ...
Page 21
... This requirement includes external logic. Some external logic has the ability to power itself down into a low current state by monitoring the PWREN# signal. For external logic that cannot power itself down in this way, the FT200XD provides a simple but effective method of turning off power during the USB suspend mode. ...
Page 22
... If the slave (FT200XD) exists on the bus then it will respond with an ACK bit (active low for acknowledged) for that address. The master then continues in either transmit or receive mode (according to the read/write bit it sent), and the slave continues in its complementary mode (receive or transmit, respectively) ...
Page 23
... These charging profiles do not enumerate the USB port of the peripheral. The FT200XD device will detect that a USB compliant dedicated charging port (DCP) is connected. Once detected while in suspend mode a battery charge detection signal is provided to allow external logic to switch to charging mode as opposed to operation mode ...
Page 24
... For more configuration options of the LTC4053 refer to: AN_175_Battery Charging Over USB Note: If the FT200XD is connected to a standard host port such that the device is enumerated the battery charge detection signal is inactive as the device will not be in suspend. Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No ...
Page 25
... This section covers transfer of data only. The USB and I also be used for programming of the MTP memory, which is covered in a separate section. Throughout this section, the reference FT-X applies to the FT200XD and FT201X devices, as the other members of the FT-X family do not have I 9.1 Host Interface (USB) From the host computer’ ...
Page 26
... Manager and no COM port is exposed. When the VCP is enabled, the device will appear under both the Universal Serial Bus Controllers and the Ports (COM & LPT) sections in Device Manager. The VCP interface will be disabled by default in the FT200XD and FT201X but can be enabled in one of the following ways: ...
Page 27
... Figure 9.1: Data transfers using 7-bit addressing The figure below summarises all of the transfers available (7-bit and 10-bit addressing). Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 2 C slave. Data transfers take the same form ...
Page 28
... Check the I2C_RXF# line, which indicates whether the Receive buffer is full. This line indicates that there is at least one empty byte available in the buffer. However, there is no indication of Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 2 C toward the host computer important to check if there is Version 1 ...
Page 29
... Suspended. 0x01 = Default. 0x02 = Addressed. 0x03 = Configured. Note: The Configured state is the normal operating state. Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 2 C read cycle following this command, the Version 1.3 2 ...
Page 30
... Note: In the case where the master keeps ACKing the data, it has to wrap around and the slave (the FT- X) will keep sending the 3 bytes of its ID. Figure 9.7: Reading the Device ID Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Version 1.3 30 ...
Page 31
... Following a power-on reset or a USB reset the FT200XD will scan its internal MTP memory and read the USB configuration descriptors stored there In many cases, the default values programmed into the MTP memory will be suitable and no re- programming will be necessary ...
Page 32
... Programming the MTP memory over I In the FT200XD device possible to program the MTP memory over its I interface which is used in the normal application of the FT200XD and would normally be connected to the master implemented in a microcontroller (MCU) or FPGA. However, special commands can also be used to access the MTP memory in the FT200XD over the same I read and write locations in the MTP memory ...
Page 33
... VID, PID and string descriptions) and also values which set the hardware configuration (the signal assigned to each CBUS pin for example). Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 User Memory Area 2 ...
Page 34
... The first part of the communication sets the address, and this is followed by the write command along with the data to be written. The MTP memory write itself will be initiated when the FT200XD receives an MTP memory write command followed by a single data byte. The ACK phase represents the current activity of the MTP memory (whether it is busy or not busy) ...
Page 35
... S/Sr General call addr R/!W A MTP ADDR cmd 0000000 0 0001_0100 S/Sr General call addr R/!W A MTP WR cmd Figure 10.3 Read EEPROM command sequence Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 0 A/!A Sr Slave addr R/!W A MTP Memory Address Phase 0 A/!A ...
Page 36
... This package is nominally 3.00mm x 3.00mm. The solder pads are on a 0.50 mm pitch. The above mechanical drawing shows the DFN-10 package. All dimensions are in millimetres. The centre pad on the base of the FT200XD is internally connected to GND. Do not place tracks on the top layer of the PCB in this area. ...
Page 37
... FT200XD 5 The date code format is YYXWW where XWW = 2 digit week number digit year number. The code XXXXXXX is the manufacturing LOT code. Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Version 1.3 Line 1 – ...
Page 38
... Figure 11.2 FT200XD Solder Reflow Profile The recommended values for the solder reflow profile are detailed in Table 11.1. Values are shown for both a completely Pb free solder process (i.e. the FT200XD is used with Pb free solder), and for a non-Pb free solder process (i.e. the FT200XD is used with non-Pb free solder). ...
Page 39
... Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Branch Office – Hillsboro, Oregon, USA ...
Page 40
... Appendix A – References Useful Application Notes http://www.ftdichip.com/Documents/AppNotes/AN232R-01_FT232R_BitBangModes.pdf http://www.ftdichip.com/Documents/AppNotes/AN_107_AdvancedDriverOptions_AN_000073.pdf http://www.ftdichip.com/Documents/AppNotes/AN_121_FTDI_Device_EEPROM_User_Area_Usage.pdf http://www.ftdichip.com/Documents/InstallGuides.htm http://www.ftdichip.com/Support/Documents/TechnicalNotes/TN_100_USB_VID-PID_Guidelines.pdf http://www.ftdichip.com/Support/Documents/AppNotes/AN_175_Battery%20Charging%20Over%20USB %20with%20FTEX%20Devices.pdf http://i2c2p.twibright.com/spec/i2c.pdf http://www.usb.org/developers/devclass_docs/BCv1.2_011912.zip Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 Version 1.3 40 ...
Page 41
... Figure 9.7: Reading the Device ID ................................................................................................ 30 Figure 10.1 Simplified memory map for the FT-X ............................................................................ 33 Figure 10.2 Write EEPROM command sequence .............................................................................. 35 Figure 10.3 Read EEPROM command sequence ............................................................................... 35 Figure 11.1 DFN-10 Package Dimensions ....................................................................................... 36 Figure 11.2 FT200XD Solder Reflow Profile ..................................................................................... 38 List of Tables Table 1.1 Ordering part numbers .................................................................................................... 2 Table 3.1 Power and Ground .......................................................................................................... 7 Table 3.2 Common Function pins .................................................................................................... 7 2 Table 3 ...
Page 42
... Removed section 8.3 showing connection of the Tx/Rx LEDs. Version 1.3 Added 5V tolerant statement on front page Updated TID info Updated US address Copyright © 2013 Future Technology Devices International Limited FT200XD USB I2C SLAVE IC Datasheet Document No.: FT_000628 Clearance No.: FTDI# 265 USB I2C SLAVE IC FT200XD FT_000628 FTDI# 265 http://www.ftdichip.com/Products/ICs/FTEX.htm Send Feedback Version 1 ...