MAX3140EEI-T Maxim Integrated, MAX3140EEI-T Datasheet - Page 26
![no-image](/images/no-image-200.jpg)
MAX3140EEI-T
Manufacturer Part Number
MAX3140EEI-T
Description
UART Interface IC
Manufacturer
Maxim Integrated
Type
SPI/MICROWIRE-Compatible UART with Integrated ESD-Protected RS-485/RS-422 Transceiverr
Datasheet
1.MAX3140EEI-T.pdf
(36 pages)
Specifications of MAX3140EEI-T
Data Rate
115 Kbps, 500 Kbps, 10Mbps
Supply Voltage - Max
5.25 V
Supply Voltage - Min
4.75 V
Supply Current
0.7 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Description/function
SPI/MICROWIRE-Compatible UART with integrated RS-485/RS-422 transceivers
Mounting Style
SMD/SMT
Operating Supply Voltage
5 V
SPI/MICROWIRE-Compatible UART with Integrated
True Fail-Safe RS-485/RS-422 Transceivers
The MAX3140 supports a common multidrop communi-
cation technique referred to as 9-bit mode. In this
mode, the parity bit is set to indicate a message that
contains a header with a destination address. Set the
MAX3140’s parity mask to generate interrupts for this
condition. Operating a network in this mode reduces
the processing overhead of all nodes by enabling the
slave controllers to ignore most message traffic. This
relieves the remote processor to handle more useful
tasks.
In 9-bit mode, the MAX3140 is set up with eight bits
plus parity. The parity bit in all normal messages is
clear, but is set in an address-type message. The
MAX3140’s parity-interrupt mask generates an interrupt
on high parity when enabled. When the master sends
an address message with the parity bit set, all
MAX3140 nodes issue an interrupt. All nodes then
retrieve the received byte to compare to their assigned
address. Once addressed, the node continues to
process each received byte. If the node was not
addressed, it ignores all message traffic until a new
address is sent out by the master.
The parity/9th-bit interrupt is controlled only by the data
in the receive register and is not affected by data in the
FIFO, so the most effective use of the parity/9th-bit
interrupt is with FIFO disabled. With the FIFO disabled,
received nonaddress words are ignored and not even
read from the UART.
Figure 16. IrDA Timing
26
______________________________________________________________________________________
NORMAL UART
NORMAL
IrDA
IrDA
RX
RX
TX
TX
0
1
1
0
0
1
1
UART FRAME
DATA BITS
0
0
0
0
9-Bit Networks
1
1
1
1
0
0
1
1
The MAX3140’s IrDA mode communicates with other
IrDA SIR-compatible devices, or reduces power con-
sumption in opto-isolated applications.
In IrDA mode, a bit period is shortened to 3/16 of a
baud period (1.61µs at 115,200 baud) (Figure 16). A
data zero is transmitted as a pulse of light (TX = logic
low, RX = logic high).
In receive mode, the RX signal’s sampling is done
halfway into the transmission of a high level. The sam-
pling is done once, instead of three times, as in normal
mode. The MAX3140 ignores pulses shorter than
approximately 1/16 of the baud period. The IrDA device
that is communicating with the MAX3140 must transmit
pulses at 3/16 of the baud period. For compatibility with
other IrDA devices, set the format to 8-bit data, one
stop, no parity.
The standard RS-485 receiver input impedance is 12kΩ
(one unit load), and the standard driver can drive up to
32 unit loads. The MAX3140 has a 1/8-unit-load receiver
input impedance (96kΩ), allowing up to 256 trans-
ceivers to be connected in parallel on one communica-
tion line. Any combination of these devices and/or other
RS-485 transceivers with a total of 32 unit loads or less
can be connected to the line.
The MAX3140 with SRL = V
rate limited, minimizing EMI and reducing reflections
caused by improperly terminated cables. Figure 17
shows the driver output waveform and its Fourier analy-
Figure 17. Driver Output Waveform and FFT Plot of MAX3140
with SRL = GND, Transmitting at 20kHz
20dB/div
Reduced EMI and Reflections for the
256 RS-485 Transceivers on the Bus
0
100kHz/div
CC
RS-485/RS-422 Driver
or unconnected, is slew-
SIR IrDA Mode
1MHz