MAX8563EEE-T Maxim Integrated, MAX8563EEE-T Datasheet - Page 10

• Manufacturer Part Number: MAX8563EEE-T
• Description: Low Dropout Controllers - LDO
• Manufacturer: Maxim Integrated

Specifications of MAX8563EEE-T

• Input Voltage Max: 13.2 V
• Input Voltage Min: 4.5 V

Set R
V
state, and that V
Example: Connect 100k
EN_ to IN_. Thus, when V
V
V
Alternately, to avoid fault shutdown due to the delay of
V
logic and only drive high when V
state value.
The output voltage range at the source of the n-MOSFET
is from 0.5V to 3.3V when V
1.8V when V
function of the minimum gate-to-source voltage (V
the MOSFET and V
The external n-MOSFET contains a parasitic diode from
source to drain. If the output is ever anticipated to
exceed the input, current flows from source to drain. If
this is undesirable, external protection is needed. A
simple solution is the placement of a diode in series,
from IN_ to the drain of the n-MOSFET, so that reverse
current is not possible. Due to the forward-voltage drop
of the diode, the maximum output voltage is reduced
and additional power is consumed in the diode.
The MAX8563/MAX8564/MAX8564A have independent
enable control inputs (EN1, EN2, and EN3). Drive EN1
high to enable output 1. Drive EN2 high to enable out-
put 2. Drive EN3 high to enable output 3. When EN_ is
driven low, the corresponding DRV_ is internally pulled
to GND and POK_ is internally pulled low.
±1%, Ultra-Low Output Voltage, Dual and Triple
Linear n-FET Controllers
Figure 4. Voltage-Divider on EN_
10
DD
EN
EN
IN
_ = 0.46V. When V
_ = 1.6V.
relative to V
______________________________________________________________________________________
> V
D
= 100k . The above equations also assume that
IN_
1 3 .
> 1V when V
DD
R
DD
DD
is 5V. The maximum output voltage is a
E
R
MAX8564A
, pull EN_ low with a separate control
DD
MAX8563
MAX8564
E
> 3V.
R
D
.
DD
DD
from EN to V
IN_
EN_
= 12V and V
DD
V
= 12V and V
DD
is on or at a high-voltage
is 12V and from 0.5V to
IN
V
Enable and POK
IN
Output Voltage
R
R
D
E
reaches a steady-
_
V
IN_
DD
DD
IN
V
_ = 1.2V, then
IN
and 4k
IN
_ = 0V, then
_
GS
from
) of
The POK_ is an open-drain output that provides the sta-
tus of the output voltage and pulls low depending upon
circuit conditions. During startup, once the FB_ reaches
the POK_ threshold, the POK_ signal goes high. The
POK_ threshold has 30mV of hysteresis. When the out-
put voltage drops 12% below the nominal regulated
voltage, POK_ pulls low. All POK_ outputs pull low
when UVLO is activated or when the internal VL regula-
tor and reference are not ready.
When an overload event or short circuit occurs, the
device that is most vulnerable is the external n-MOSFET.
The MAX8563/MAX8564/MAX8564A monitor the output
voltage to protect the MOSFET. When DRV_ is at its maxi-
mum voltage and the output voltage drops below 80%
but is still greater than 60% of its nominal voltage for
more than 50µs, the MAX8563/MAX8564/MAX8564A
shut down that particular regulator output by pulling
DRV_ to GND. Note that there is an additional inherent
delay in turning off the MOSFET. The delay is a function
of the compensation capacitor and the MOSFET. If the
output recovers to greater than 80% within 50µs, it is not
considered to be in overload and no action is taken.
When the output voltage drops below 60% of its nominal
voltage, the MAX8563/MAX8564/MAX8564A immediately
shut down that particular regulator output by pulling
DRV_ to GND. To restart that particular LDO, V
be recycled below the UVLO or the corresponding EN_
must be recycled. The overload protection is shown in
the Typical Operating Characteristics.
The minimum output voltage for each controller of the
MAX8563/MAX8564/MAX8564A is typically 0.5V. The
maximum output voltage is adjustable up to 3.3V with
V
put voltage, connect the FB_ pin to the center of a volt-
age-divider between OUT_ and GND (Figure 5). The
resistor-divider current should be at least 1mA per 1A of
maximum output current; i.e., for a 3A maximum output
current, set the resistor-divider bias current to
R
DD
B
= 12V, and up to 1.8V with V
I
OUT MIN
V
FB
(
I
OUT MIN
)
(
1000
Output Undervoltage and
)
Output Voltage Setting
Design Procedure
I
Overload Protection
OUT MAX
I
OUT MAX
1000
DD
V
(
FB
(
= 5V. To set the out-
)
)
I
OUT MAX
3mA:
DD
500
(
must
)