DS32508-W Maxim Integrated, DS32508-W Datasheet - Page 26
DS32508-W
Manufacturer Part Number
DS32508-W
Description
Network Controller & Processor ICs
Manufacturer
Maxim Integrated
Datasheet
1.DS32512W.pdf
(130 pages)
Specifications of DS32508-W
Part # Aliases
90-32508-W00
- Current page: 26 of 130
- Download datasheet (2Mb)
8.2.9 Driver Monitor and Output Failure Detection
The transmit driver monitor compares the amplitude of the transmit waveform to thresholds V
the amplitude is less than V
activates the
of LIU.SR:TDM can cause an interrupt if enabled by LIU.SRIE:TDMIE. When the transmitter is disabled, the
transmit driver monitor is also disabled. The transmit driver monitor is clocked by the LIU’s reference clock.
Note that the transmit driver monitor can be affected by reflections caused by shorts and opens on the line. A short
circuit at a distance less than a few inches (~11 inches for FR-4 material) can introduce inverted reflections that
reduce the outgoing pulse amplitude below the V
status bit. Similarly an open circuit a similar distance away can introduce noninverted reflections that increase the
outgoing amplitude above the V
and opens at larger distances away from
this effect is data-pattern dependent.
If either
declared by setting the LIU.SR:TFAIL status bit. A change of state of the TFAIL status bit can cause an interrupt if
enabled by LIU.SRIE:TFAILIE. TFAIL is cleared when activity is detected on both
8.2.10 Power-Down
To minimize power consumption when the transmitter is not being used, the
PORT.CR1:TPD configuration bit (per port) can be asserted. When the transmitter is powered down, the
TXN
8.2.11 Jitter Generation (Intrinsic)
The transmitter meets the jitter generation requirements of all applicable standards in
jitter attenuator enabled. Generated jitter is measured with a jitter-free, 0ppm input clock.
Table 8-1. Jitter Generation
8.2.12 Jitter Transfer
Without the jitter attenuator on the transmit side, the transmitter passes jitter through unchanged. With the jitter
attenuator enabled on the transmit side, the transmitter meets the jitter transfer requirements of all applicable
telecommunication standards in
SIGNAL STANDARD REQUIREMENT
STS-1
STS-1
DS3
DS3
DS3
E3
pins are put in a high-impedance state and the transmit drivers are powered down.
TXP
TDM
or
GR-499
GR-253
GR-253
T1.404
T1.404
G.751
TXN
output pin (if the hardware interface is enabled) and sets the LIU.SR:TDM status bit. The setting
is not connected (open), shorted to V
TXMIN
0.01 UI
0.05 UI
0.05 UI
0.10 UI
0.3 UI
0.5 UI
TXMAX
Table
or greater than V
RMS
P-P
RMS
threshold and thereby activate the
P-P
P-P
P-P
1-1. See
TXP/TXN
100Hz to 800kHz
30kHz to 400kHz
12kHz to 400kHz
12kHz to 400kHz
Figure
10Hz to 400kHz
10Hz to 400kHz
BANDWIDTH
TXMIN
26 of 130
can also activate the
TXMAX
threshold and thereby activate the
8-7.
for approximately 32 MCLK cycles, then the monitor
DD
, or shorted to V
WITHOUT CLAD
0.015
0.005
TYP
0.01
0.02
0.02
0.04
TDM
TDM
DS325xx JITTER
pin and/or the TDM status bit. Shorts
SS
0.025
0.008
MAX
pin and/or the TDM status bit, but
0.02
0.03
0.03
0.06
TXP
, then a transmit failure alarm is
DS32506/DS32508/DS32512
Table
TPD
and
0.007
WITH CLAD
TDM
TYP
0.01
0.05
0.04
0.04
0.06
TXN
8-1, with or without the
pin (all ports) or the
.
pin and/or the TDM
TXMIN
MAX
0.02
0.06
0.05
0.05
0.01
0.08
and V
TXP
UNITS
UI
UI
TXMAX
UI
UI
UI
UI
RMS
RMS
P-P
P-P
P-P
P-P
and
. If
Related parts for DS32508-W
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: