M24C32-WDW6TP STMicroelectronics, M24C32-WDW6TP Datasheet - Page 16
![IC EEPROM 32KBIT 400KHZ 8TSSOP](/photos/5/43/54342/497-8-tssop_sml.jpg)
M24C32-WDW6TP
Manufacturer Part Number
M24C32-WDW6TP
Description
IC EEPROM 32KBIT 400KHZ 8TSSOP
Manufacturer
STMicroelectronics
Specifications of M24C32-WDW6TP
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
32K (4K x 8)
Speed
400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-TSSOP
Density
32Kb
Interface Type
Serial (I2C)
Organization
4Kx8
Access Time (max)
900ns
Frequency (max)
400KHz
Write Protection
Yes
Data Retention
40Year
Operating Supply Voltage (typ)
3.3/5V
Package Type
TSSOP
Operating Temp Range
-40C to 85C
Supply Current
5mA
Operating Supply Voltage (min)
2.5V
Operating Supply Voltage (max)
5.5V
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
8
Maximum Clock Frequency
0.4 MHz
Access Time
900 ns
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.5 V
Maximum Operating Current
2 mA
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
2.5 V, 5.5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-8645-2
M24C32-WDW6TP
M24C32-WDW6TP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M24C32-WDW6TP
Manufacturer:
STM
Quantity:
1 079
Company:
Part Number:
M24C32-WDW6TP/K
Manufacturer:
ST
Quantity:
2 278
Device operation
4.6
4.7
4.8
16/38
Write operations
Following a Start condition the bus master sends a device select code with the Read/Write
bit (RW) reset to 0. The device acknowledges this, as shown in
address bytes. The device responds to each address byte with an acknowledge bit, and
then waits for the data Byte.
Writing to the memory may be inhibited if Write Control (WC) is driven high. Any Write
instruction with Write Control (WC) driven high (during a period of time from the Start
condition until the end of the two address bytes) will not modify the memory contents, and
the accompanying data bytes are not acknowledged, as shown in
Each data byte in the memory has a 16-bit (two byte wide) address. The Most Significant
Byte
form the address of the byte in memory.
When the bus master generates a Stop condition immediately after the Ack bit (in the “10
bit” time slot), either at the end of a Byte Write or a Page Write, the internal Write cycle is
triggered. A Stop condition at any other time slot does not trigger the internal Write cycle.
After the Stop condition, the delay t
the device’s internal address counter is incremented automatically, to point to the next byte
address after the last one that was modified.
During the internal Write cycle, Serial Data (SDA) is disabled internally, and the device does
not respond to any requests.
Byte Write
After the device select code and the address bytes, the bus master sends one data byte. If
the addressed location is Write-protected, by Write Control (WC) being driven high, the
device replies with NoAck, and the location is not modified. If, instead, the addressed
location is not Write-protected, the device replies with Ack. The bus master terminates the
transfer by generating a Stop condition, as shown in
Page Write
The Page Write mode allows up to 32 bytes to be written in a single Write cycle, provided
that they are all located in the same ‘row’ in the memory: that is, the most significant
memory address bits (b11-b5) are the same. If more bytes are sent than will fit up to the end
of the row, a condition known as ‘roll-over’ occurs. This should be avoided, as data starts to
become overwritten in an implementation dependent way.
The bus master sends from 1 to 32 bytes of data, each of which is acknowledged by the
device if Write Control (WC) is low. If Write Control (WC) is high, the contents of the
addressed memory location are not modified, and each data byte is followed by a NoAck.
After each byte is transferred, the internal byte address counter (inside the page) is
incremented. The transfer is terminated by the bus master generating a Stop condition.
(Table
3) is sent first, followed by the Least Significant Byte
Doc ID 4578 Rev 17
W
, and the successful completion of a Write operation,
Figure
M24C32-W M24C32-R M24C32-F
8.
Figure
(Table
Figure
8, and waits for two
4). Bits b15 to b0
7.
th