AT89C51RC2-RLTIL Atmel, AT89C51RC2-RLTIL Datasheet - Page 69

• Manufacturer Part Number: AT89C51RC2-RLTIL
• Description: 8-bit Microcontrollers - MCU 80C31 w/4k
• Manufacturer: Atmel

Specifications of AT89C51RC2-RLTIL

• Product Category: 8-bit Microcontrollers - MCU
• Core: 8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 60 MHz
• Program Memory Size: 32 KB
• Data Ram Size: 1280 B
• On-chip Adc: No
• Operating Supply Voltage: 2.7 V to 5.5 V
• Package / Case: VQFP-44
• Mounting Style: SMD/SMT
• Interface Type: SPI, UART
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Program Memory Type: Flash
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 2.7 V

Baud Rate
4180E–8051–10/06
drive the network. The Master may select each Slave device by software through port
pins (Figure 26). To prevent bus conflicts on the MISO line, only one slave should be
selected at a time by the Master for a transmission.
In a Master configuration, the SS line can be used in conjunction with the MODF flag in
the SPI Status register (SPSTA) to prevent multiple masters from driving MOSI and
SCK (see Error conditions).
A high level on the SS pin puts the MISO line of a Slave SPI in a high-impedance state.
The SS pin could be used as a general-purpose if the following conditions are met:
•
•
Note:
In Master mode, the baud rate can be selected from a baud rate generator which is con-
trolled by three bits in the SPCON register: SPR2, SPR1 and SPR0.The Master clock is
selected from one of seven clock rates resulting from the division of the internal clock by
2, 4, 8, 16, 32, 64 or 128.
Table 54 gives the different clock rates selected by SPR2:SPR1:SPR0.
Table 54. SPI Master Baud Rate Selection
SPR2
The device is configured as a Master and the SSDIS control bit in SPCON is set.
This kind of configuration can be found when only one Master is driving the network
and there is no way that the SS pin could be pulled low. Therefore, the MODF flag in
the SPSTA will never be set
The Device is configured as a Slave with CPHA and SSDIS control bits set
kind of configuration can happen when the system comprises one Master and one
Slave only. Therefore, the device should always be selected and there is no reason
that the Master uses the SS pin to select the communicating Slave device.
0
0
0
0
1
1
1
1
1. Clearing SSDIS control bit does not clear MODF.
2. Special care should be taken not to set SSDIS control bit when CPHA = ’0’ because
in this mode, the SS is used to start the transmission.
SPR1
0
0
1
1
0
0
1
1
SPR0
0
1
0
1
0
1
0
1
(1)
.
F
F
F
F
F
F
CLK PERIPH
F
Clock Rate
CLK PERIPH
CLK PERIPH
CLK PERIPH
CLK PERIPH
CLK PERIPH
CLK PERIPH
Don’t Use
/128
/16
/32
/64
/8
/2
/4
AT89C51RB2/RC2
Baud Rate Divisor (BD)
No BRG
128
16
32
64
2
4
8
(2)
. This
69