IS24C02D-2SLI-TR ISSI, Integrated Silicon Solution Inc, IS24C02D-2SLI-TR Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/347/issi__integrated_silicon_solution_inc_sml.jpg)
IS24C02D-2SLI-TR
Manufacturer Part Number
IS24C02D-2SLI-TR
Description
IC EEPROM 2KBIT 1MHZ 8MSOP
Manufacturer
ISSI, Integrated Silicon Solution Inc
Datasheet
1.IS24C02D-2GLI-TR.pdf
(21 pages)
Specifications of IS24C02D-2SLI-TR
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
2K (256 x 8)
Speed
1MHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
– During a data transfer, the SDA line must remain stable
the High period of the clock signal. The data on the SDA
line may be changed during the Low period of the clock
SCL is High. The IS24C02D monitors the SDA and SCL
lines and will not respond until the Start condition is met.
pulls down the SDA line.
remain in it until SCL or SDA toggles; b) Following the Stop
signal if no write operation is initiated; or c) Following any
internal write operation.
IS24C02D
The bus Protocol:
– Data transfer may be initiated only when the bus is not
The state of the SDA line represents valid data after a Start
condition. The SDA line must be stable for the duration of
signal. There is one clock pulse per bit of data. Each data
transfer is initiated with a Start condition and terminated
with a Stop condition.
Start Condition
The Start condition precedes all commands to the device
and is defined as a High to Low transition of SDA when
Stop Condition
The Stop condition is defined as a Low to High transition
of SDA when SCL is High. All operations must end with
a Stop condition.
Acknowledge (ACK)
After a successful data transfer, each receiving device is
required to generate an ACK. The Acknowledging device
Reset
The IS24C02D contains a reset function in case the
2-wire bus transmission is accidentally interrupted (eg. a
power loss), or needs to be terminated mid-stream. The
reset is caused when the Master device creates a Start
condition. To do this, it may be necessary for the Master
device to monitor the SDA line while cycling the SCL up
to nine times. (For each clock signal transition to High,
the Master checks for a High level on SDA.)
Standby Mode
Power consumption is reduced in standby mode. The
IS24C02D will enter standby mode: a) At Power-up, and
6
busy
whenever the SCL line is high. Any changes in the SDA
line while the SCL line is high will be interpreted as a
Start or Stop condition.
DEVICE ADDRESSInG
The Master begins a transmission by sending a Start
condition. The Master then sends the address of the
particular Slave devices it is requesting. The Slave device
(Fig. 5) address is 8 bits.
The four most significant bits of the Slave device address
are fixed as 1010 for normal read/write operations, and
0110 for permanent write-protection operations.
This device has three address bits (A1, A2, and A0) that
allow up to eight IS24C02D devices to share the 2-wire
bus. Upon receiving the Slave address, the device
compares the three address bits with the hardwired
A2, A1, and A0 input pins to determine if it is the
appropriate Slave. If any of the A2 - A0 pins is neither
biased to High nor Low, internal circuitry defaults the
value to Low.
The last bit of the Slave address specifies whether a Read
or Write operation is to be performed. When this bit is set
to 1, a Read operation is selected, and when set to 0, a
Write operation is selected.
After the Master transmits the Start condition and Slave
address byte (Fig. 5), the appropriate 2-wire Slave (eg.
IS24C02D) will respond with ACK on the SDA line. The
Slave will pull down the SDA on the ninth clock cycle,
signaling that it received the eight bits of data. The
selected IS24C02D then prepares for a Read or Write
operation by monitoring the bus.
Integrated Silicon Solution, Inc. — www.issi.com
07/30/09
Rev. C