EN2340QI-E Enpirion, EN2340QI-E Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/2/224/enpirion_sml.jpg)
EN2340QI-E
Manufacturer Part Number
EN2340QI-E
Description
Power Management IC Development Tools EVAL FOR EN2340QI
Manufacturer
Enpirion
Type
DC/DC Converters, Regulators & Controllersr
Datasheet
1.EN2340QI-E.pdf
(20 pages)
Specifications of EN2340QI-E
Rohs
yes
Product
Evaluation Boards
Tool Is For Evaluation Of
EN2340QI
Input Voltage
4.5 V to 14 V
Output Voltage
5 V
Output Current
4 A
Spread Spectrum Mode
The external clock frequency may be swept
between 0.9MHz and 1.3MHz at repetition
rates of up to 10 kHz in order to reduce EMI
frequency components.
Soft-Start Operation
Soft start is a means to ramp the output voltage
gradually upon start-up. The output voltage rise
time is controlled by the choice of soft-start
capacitor, which is placed between the SS pin (pin
56) and the AGND pin (pin 52).
During start-up of the converter, the reference
voltage to the error amplifier is linearly increased to
its final level by an internal current source of
approximately 10µA. Typical soft-start rise time is
~3.2ms with SS capacitor value of 47nF. The rise
time is measured from when V
ENABLE pin voltage crosses its logic high
threshold to when V
value.
POK Operation
The POK signal is an open drain signal (requires a
pull up resistor to AVIN or similar voltage) from the
converter indicating the output voltage is within the
specified range. Typically, a 100kΩ or lower
resistance is used as the pull-up resistor. The POK
signal will be logic high (AVIN) when the output
voltage is above 90% of the programmed V
the output voltage goes outside of this range, the
POK signal will be a logic low.
Over-Current Protection (OCP)
The current limit function is achieved by sensing
the current flowing through a sense PFET. When
the sensed current exceeds the current limit, both
power FETs are turned off for the rest of the
switching cycle.
removed, the over-current protection circuit will re-
enable PWM operation. If the over-current condition
persists, the circuit will continue to protect the load.
Application Information
Output Voltage Programming and Loop
Compensation
The EN2340QI output voltage is programmed using
a simple resistor divider network. A phase lead
capacitor (C
stabilizing the loop. Figure 6 shows the required
©Enpirion 2012 all rights reserved, E&OE
06878
Rise Time (ms): T
A
) plus a resistor (R
If the over-current condition is
OUT
R
reaches its programmed
≈ C
ss
[nF] x 0.067
CA
IN
) are required for
> V
UVLOR
OUT
and
. If
Enpirion Confidential
April 16, 2012
The OCP trip point is nominally set as specified in
the Electrical Characteristics table. In the event the
OCP circuit trips consistently in normal operation,
the device enters a hiccup mode. While in hiccup
mode, the device is disabled for a short while and
restarted with a normal soft-start. The hiccup time
is approximately 32ms.
indefinitely as long as the over current condition
persists.
The OCP trip point can be programmed to trip at a
lower level via the RCLX pin. The value of the
resistor connected between RCLX and ground will
determine the OCP trip point. Generally, the higher
the RCLX value, the higher the current limit
threshold. Note that if RCLX pin is left open the
output current will be unlimited and the device will
not have current limit protection. Reference Table 2
for a list of recommended resistor values on RCLX
that will set the OCP trip point at the typical value of
6A, also specified in the Electrical Characteristics
table.
Thermal Overload Protection
Thermal shutdown circuit will disable device
operation when the junction temperature exceeds
approximately 150ºC. After a thermal shutdown
event, when the junction temperature drops by
approx 20ºC, the converter will re-start with a
normal soft-start.
Input Under-Voltage Lock-Out (UVLO)
Internal circuits ensure that the converter will not
start switching until the input voltage is above the
specified minimum voltage. Hysteresis, input de-
glitch and output leading edge blanking ensures
high noise immunity and prevents false UVLO
triggers.
components and the equations to calculate their
values. The values recommended for C
will vary with each PVIN and VOUT combination.
The EN2340 solution can be optimized for either
smallest size or highest performance. Please see
Table 5 for a list of recommended C
values for each solution option.
0.75V < V
1.2V < V
2.0V < V
Table 2: Recommended R
V
OUT
Range
OUT
OUT
OUT
≤ 2.0V
≤ 5.0V
≤ 1.2V
www.enpirion.com, Page 12
This cycle can continue
CLX
Values vs. V
R
CLX
31.6kΩ
33.2kΩ
36.5kΩ
Value
EN2340QI
A
A
and R
and R
OUT
Rev: B
CA
CA