MT46H32M32LFCM-6 IT:A TR Micron Technology Inc, MT46H32M32LFCM-6 IT:A TR Datasheet - Page 18
![IC DDR SDRAM 1GBIT 90VFBGA](/photos/7/23/72313/mfg557-90-vfbga_sml.jpg)
MT46H32M32LFCM-6 IT:A TR
Manufacturer Part Number
MT46H32M32LFCM-6 IT:A TR
Description
IC DDR SDRAM 1GBIT 90VFBGA
Manufacturer
Micron Technology Inc
Datasheet
1.MT46H64M16LFCK-5A_TR.pdf
(95 pages)
Specifications of MT46H32M32LFCM-6 IT:A TR
Format - Memory
RAM
Memory Type
Mobile DDR SDRAM
Memory Size
1G (32M x 32)
Speed
166MHz
Interface
Parallel
Voltage - Supply
1.7 V ~ 1.95 V
Operating Temperature
-40°C ~ 85°C
Package / Case
90-VFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
557-1333-2
Table 5: AC/DC Electrical Characteristics and Operating Conditions (Continued)
Notes 1–5 apply to all parameters/conditions in this table; V
Table 6: Capacitance (x16, x32)
Note 1 applies to all the parameters in this table
PDF: 09005aef82ce3074
1gb_ddr_mobile_sdram_t48m.pdf - Rev. K 07/09 EN
Parameter/Condition
Output leakage current
(DQ are disabled; 0V ≤ V
Operating temperature
Commercial
Industrial
Parameter
Input capacitance: CK, CK#
Notes:
OUT
≤ V
10. CK and CK# input slew rate must be ≥1 V/ns (2 V/ns if measured differentially).
11. V
12. The value of V
13. DQ and DM input slew rates must not deviate from DQS by more than 10%. 50ps must
1. All voltages referenced to V
2. All parameters assume proper device initialization.
3. Tests for AC timing, I
4. Outputs measured with equivalent load; transmission line delay is assumed to be very
5. Timing and I
6. Any positive glitch must be less than one-third of the clock cycle and not more than
7. V
8. To maintain a valid level, the transitioning edge of the input must:
9. V
DDQ
nominal supply voltage levels, but the related specifications and device operation are
guaranteed for the full voltage range specified.
small:
but input timing is still referenced to V
output timing reference voltage level is V
+200mV or 2.0V, whichever is less. Any negative glitch must be less than one-third of
the clock cycle and not exceed either –150mV or +1.6V, whichever is more positive.
8a. Sustain a constant slew rate from the current AC level through to the target AC lev-
el, V
8b. Reach at least the target AC level.
8c. After the AC target level is reached, continue to maintain at least the target DC lev-
el, V
be greater than one-third of the cycle rate. V
width ≤3ns and the pulse width cannot be greater than one-third of the cycle rate.
el on CK#.
variations in the DC level of the same.
be added to
4 V/ns, functionality is uncertain.
)
DD
IH
ID
overshoot: V
is the magnitude of the difference between the input level on CK and the input lev-
and V
IL(AC)
IL(DC)
I/O
or V
or V
DDQ
Full drive strength
DD
t
DS and
IH(AC)
IH(DC)
must track each other and V
IX
tests may use a V
IH,max
50
is expected to equal V
Symbol
.
.
I
T
T
DD
t
OZ
DH for each 100 mV/ns reduction in slew rate. If slew rate exceeds
A
A
= V
, and electrical AC and DC characteristics may be conducted at
Symbol
DD
DDQ
18
C
/V
SS
20pF
CK
DDQ
.
+ 1.0V for a pulse width ≤3ns and the pulse width cannot
IL
= 1.70–1.95V
-to-V
1Gb: x16, x32 Mobile LPDDR SDRAM
Min
I/O
–40
Micron Technology, Inc. reserves the right to change products or specifications without notice.
–5
0
DDQ
IH
DDQ
Half drive strength
Min
1.5
swing of up to 1.5V in the test environment,
DDQ
/2 of the transmitting device and must track
/2 (or to the crossing point for CK/CK#). The
DDQ
IL
/2.
50
must be less than or equal to V
undershoot: V
Max
Max
Electrical Specifications
+70
+85
3.0
5
10pF
©2007 Micron Technology, Inc. All rights reserved.
IL,min
= –1.0V for a pulse
Unit
pF
Unit
μA
˚C
˚C
DD
Notes
Notes
.