DS28E04S-100+T Maxim Integrated Products, DS28E04S-100+T Datasheet - Page 11

IC EEPROM 4KBIT 16SOIC

DS28E04S-100+T

Manufacturer Part Number
DS28E04S-100+T
Description
IC EEPROM 4KBIT 16SOIC
Manufacturer
Maxim Integrated Products
Datasheet

Specifications of DS28E04S-100+T

Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
4K (256 x 16)
Interface
1-Wire Serial
Operating Temperature
-40°C ~ 85°C
Package / Case
16-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Supply
-
Speed
-
Conditional Search Channel Polarity Selection Register
The data in this register specifies the polarity of each selected PIO channel for the device to respond to the
conditional search command. This register can only be written through the Write Registers command. Within a PIO
channel, the data source may be either the channel's input pin or the channel's activity latch, as specified by the
PLS bit in the Control/Status register at address 0225h. This register is read/write. Each bit is associated with the
respective PIO channel as shown in Figure 7. Bits 2 to 7 have no function; they always read 0 and cannot be
changed to 1. This register is cleared to 00h at power-up.
Control/Status Register
The data in this register reports status information and further configures the device for conditional search. This
register can only be written through the Write Registers command. This register is read/write. The power-up state
of the PORL bit is "1". CT and PLS power up as "0". The functional assignments of the individual bits are explained
in the table below. Bits 2, 4, and 5 have no function; they always read 0 and cannot be set to 1.
Control/Status Register Details
PLS: Pin or Activity
Latch Select
CT: Conditional Search
Logical Term
PORL: Power-On Reset
Latch
POL: PIO Default
Polarity (Read-Only)
VCCP: V
Status (Read-Only)
ADDR
0224h
ADDR
0225h
BIT DESCRIPTION
CC
VCCP
Power
b7
b7
0
POL
b6
b6
0
BIT(S)
b0
b1
b3
b6
b7
b5
b5
0
0
Selects either the PIO pins or the PIO activity latches as input for the
conditional search.
Specifies whether the data of two channels needs to be OR’ed or
AND’ed to meet the qualifying condition for the device to respond to
a conditional search. If only a single channel is selected in the
channel selection mask (0223h) this bit is a don't care.
Specifies whether the device has performed a power-on reset. This
bit can only be cleared to 0 by writing to the Control/Status Register.
As long as this bit is 1 the device will always respond to a Conditional
Search ROM sequence.
Reports the state of the POL pin. The state of the POL pin specifies
whether the PIO pins P0 and P1 power up high or low. The polarity
of a pulse generated at a PIO pin is the opposite of the pin's power-
up state.
For V
voltage source equal to V
b4
b4
0
0
CC
-powered operation, the V
0: pin selected (default)
1: activity latch selected
0: bitwise OR (default)
1: bitwise AND
0: PIO powers up 0
1: PIO powers up 1
0: V
1: V
PORL
b3
b3
11 of 36
CC
CC
0
-powered operation
power not available
b2
b2
0
0
PUP
DEFINITION
.
SP1
CT
b1
b1
CC
pin needs to be connected to a
PLS
SP0
b0
b0

Related parts for DS28E04S-100+T