DSM2180F3-90K6 STMicroelectronics, DSM2180F3-90K6 Datasheet - Page 39

• Manufacturer Part Number: DSM2180F3-90K6
• Description: IC FLASH 1MBIT 90NS 52PLCC
• Manufacturer: STMicroelectronics

Specifications of DSM2180F3-90K6

• Format - Memory: FLASH
• Memory Type: FLASH
• Memory Size: 1M (128K x 8)
• Speed: 90ns
• Interface: Parallel
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 52-PLCC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-1335-5

POWER MANAGEMENT
The device offers configurable power saving op-
tions. These options may be used individually or in
combinations, as follows:
■
■
Table 17. Power Management Mode Registers PMMR0
Note: 1. The bits of this register are cleared to zero following Power-up. Subsequent Reset (Reset) pulses do not clear the registers.
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
All memory blocks in the device are built with
zero-power management technology. Zero-
power technology puts the memories into
standby mode when address/data inputs are
not changing (zero DC current). As soon as a
transition occurs on an input, the affected
memory “wakes up”, changes and latches its
outputs, then goes back to standby. The
designer does not have to do anything special to
achieve memory standby mode when no inputs
are changing—it happens automatically.
Both PLDs (DPLD and CPLD) are also Zero-
power, but this is not the default operation. The
DSP must set a bit at run-time to achieve Zero-
power as described next.
The PMMR registers can be written by the DSP
at run-time to manage power. The device has a
Turbo bit in the PMMR0 register. This bit can be
set to turn the Turbo mode off (the default is with
Turbo mode turned on). While Turbo mode is
off, the PLDs can achieve standby current when
no PLD inputs are changing (zero DC current).
Even when inputs do change, significant power
can be saved at lower frequencies (AC current),
X
X
X
PLD Turbo
PLD Array clk
PLD MCell clk
X
X
0
0
0
0 = on PLD Turbo mode is on
1 = off PLD Turbo mode is off, saving power.
0 = on
1 = off CLKIN (PD1) input to PLD AND Array is blocked, saving power.
0 = on CLKIN (PD1) input to the PLD Macrocells is passed onto PLDs.
1 = off CLKIN (PD1) input to PLD Macrocells is blocked, saving power.
0
0
Not used, and should be set to zero.
Not used, and should be set to zero.
Not used, and should be set to zero.
CLKIN (PD1) input to the PLD AND Array is passed onto PLDs. Every change of
CLKIN (PD1) Powers-up the PLD when Turbo bit is 0.
Not used, and should be set to zero.
Not used, and should be set to zero.
■
compared to when Turbo mode is on. When the
Turbo mode is on, there is a significant DC
current component and the AC component is
higher.
Further significant power savings can be
achieved by blocking signals that are not used
in DPLD or CPLD logic equations. The “blocking
bits” in PMMR registers can be set to logic 1 by
the DSP to block designated signals from reach-
ing both PLDs. Current consumption of the
PLDs is directly related to the composite fre-
quency of the changes on their inputs (see Fig-
ure 25), so blocking unused PLD inputs can
significantly lower PLD operating frequency and
power consumption. The DSP also has the op-
tion of blocking certain PLD input when not
needed, then letting them pass for when needed
for specific logic operations. Table 17 and Table
18 define the PMMR registers.
PSD Chip Select Input (CSI, PD2) can be used
to disable the internal memories and csiop
registers, placing them in standby mode even if
inputs are changing. This feature does not block
any internal signals or disable the PLDs. There
is a slight penalty in memory access time when
PSD Chip Select Input (CSI, PD2) makes its
initial transition from deselected to selected.
1
DSM2180F3
39/63