CY7C1270V18-375BZI Cypress Semiconductor Corp, CY7C1270V18-375BZI Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CY7C1270V18-375BZI
Manufacturer Part Number
CY7C1270V18-375BZI
Description
IC SRAM 36MBIT 375MHZ 165TFBGA
Manufacturer
Cypress Semiconductor Corp
Datasheet
1.CY7C1268V18-400BZXC.pdf
(27 pages)
Specifications of CY7C1270V18-375BZI
Format - Memory
RAM
Memory Type
SRAM - Synchronous, DDR II
Memory Size
36M (1M x 36)
Speed
375MHz
Interface
Parallel
Voltage - Supply
1.7 V ~ 1.9 V
Operating Temperature
-40°C ~ 85°C
Package / Case
165-TFBGA
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY7C1270V18-375BZI
Manufacturer:
Cypress Semiconductor Corp
Quantity:
10 000
Functional Overview
The CY7C1266V18, CY7C1277V18, CY7C1268V18, and
CY7C1270V18 are synchronous pipelined Burst SRAMs
equipped with a DDR interface.
Accesses for both ports are initiated on the Positive Input Clock
(K). All synchronous input and output timing refer to the rising
edge of the input clocks (K and K).
All synchronous data inputs (D
controlled by the rising edge of the input clocks (K and K). All
synchronous data outputs (Q
controlled by the rising edge of the input clocks (K and K).
All synchronous control (R/W, LD, BWS
input registers controlled by the rising edge of the input clock
(K\K).
CY7C1268V18 is described in the following sections. The same
basic descriptions apply to CY7C1266V18, CY7C1277V18, and
CY7C1270V18.
Read Operations
The CY7C1268V18 is organized internally as a single array of
2M x 18. Accesses are completed in a burst of two sequential
18-bit data words. Read operations are initiated by asserting
R/W HIGH and LD LOW at the rising edge of the positive input
clock
sponding 18-bit word of data from this address location is driven
onto the Q
subsequent rising edge of K the next 18-bit data word is driven
onto the Q
rising edge of the Input clock (K and K). To maintain the internal
logic, each read access must be allowed to complete. Read
accesses can be initiated on every rising edge of the positive
input clock (K).
When read access is deselected, the CY7C1268V18 completes
the pending Read transactions. Synchronous internal circuitry
automatically tri-states the outputs following the next rising edge
of the negative input clock
transition between devices without the insertion of wait states in
a depth expanded memory.
Write Operations
Write operations are initiated by asserting R/W LOW and LD
LOW at the rising edge of the positive input clock (K). The
address presented to Address inputs is stored in the Write
Address register. On the following K clock rise, the data
presented to D
Data register provided BWS
subsequent rising edge of the Negative Input Clock (K), the infor-
mation presented to D
register provided BWS
of data are then written into the memory array at the specified
location. Write accesses can be initiated on every rising edge of
the positive input clock (K). Doing so pipelines the data flow such
that 18 bits of data can be transferred into the device on every
rising edge of the input clocks (K and K).
When write access is deselected, the device ignores all inputs
after the pending write operations have been completed.
Document Number: 001-06347 Rev. *D
(K).
Following the next two K clock rising edges, the corre-
[17:0]
[17:0]
, using K as the output timing reference. On the
[17:0]
. The requested data is valid 0.45 ns from the
is latched and stored into the 18-bit Write
[1:0]
[17:0]
are both asserted active. The 36 bits
[1:0]
is also stored into the Write Data
[x:0]
[x:0]
(K).
are both asserted active. On the
) pass through output registers
) pass through input registers
This enables a seamless
[0:X]
) inputs pass through
Byte Write Operations
Byte write operations are supported by the CY7C1268V18. A
write operation is initiated as described in the
section. The bytes that are written are determined by BWS
BWS
Asserting the appropriate Byte Write Select input during the data
portion of a write latches the data being presented and written
into the device. Deasserting the Byte Write Select input during
the data portion of a write enables the data stored in the device
to that byte to remain unaltered. This feature can be used to
simplify read/modify/write operations to a byte write operation.
Double Data Rate Operation
The CY7C1268V18 enables high-performance operation
through high clock frequencies (achieved through pipelining) and
DDR mode of operation. The CY7C1268V18 requires three No
Operation (NOP) cycles when transitioning from a read to a write
cycle.
If a read occurs after a write cycle, address and data for the write
are stored in registers. The write information must be stored
because the SRAM cannot perform the last word write to the
array without conflicting with the read. The data stays in this
register until the next write cycle occurs. On the first write cycle
after the read(s), the stored data from the earlier write is written
into the SRAM array. This is called a Posted Write.
If a read is performed on the same address on which a write is
performed in the previous cycle, the SRAM reads out the most
current data. The SRAM does this by bypassing the memory
array and reading the data from the registers.
Depth Expansion
Depth expansion requires replicating the LD control signal for
each bank. All other control signals can be common between
banks as appropriate.
Programmable Impedance
An external resistor, RQ, must be connected between the ZQ pin
on the SRAM and V
driver impedance. The value of RQ must be 5x the value of the
intended line impedance driven by the SRAM. The allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15%, is between 175Ω and 350Ω
output impedance is adjusted every 1024 cycles upon power up
to account for drifts in supply voltage and temperature.
Echo Clocks
Echo clocks are provided on the DDR-II+ to simplify data capture
on high speed systems. Two echo clocks are generated by the
DDR-II+. CQ is referenced with respect to K and CQ is refer-
enced with respect to K. These are free running clocks and are
synchronized to the input clock of the DDR-II+. The timing for the
echo clocks is shown in
Valid Data Indicator (QVLD)
QVLD is provided on the DDR-II+ to simplify data capture on high
speed systems. The QVLD is generated by the DDR-II+ device
along with data output. This signal is also edge aligned with the
echo clock and follows the timing of any data pin. This signal is
asserted half a cycle before valid data arrives.
1
, which are sampled with each set of 18-bit data words.
CY7C1266V18, CY7C1277V18
CY7C1268V18, CY7C1270V18
SS
to enable the SRAM to adjust its output
“Switching Characteristics” on page
,
with V
Write Operations
DDQ
Page 8 of 27
= 1.5V. The
0
and
22.
[+] Feedback
[+] Feedback